Replacement Fan Motor For Kinmore Vent # RS-385 PHC2-171BVDO218-00

Question

Question:

I have a 13.6 volt 1.2 amp 174E23 Vent Fan Motor. Part# RS-385 PHC2-171BVDO218-00 Kinmore. Trying to locate a replacement that fits without modifying the frame assembly.

asked by: Dawn B

0

Expert Reply:

The Replacement 12V DC Motor # BVD0218-00 is the motor you need for your Kinmore vent fan.

expert reply by: Bud M

0

Answer 1

The motor you'd looked at, part #BVD0218-00 is the correct replacement for your range hood. I've confirmed this by forwarding your photo to the folks at Ventline.

view full answer...

Answer 2

The Replacement 12V DC Motor for Ventline, Ventadome, and Vanair Fans #BVD0218-00 you were looking at can be used to replace your RS-385PHC2-17100B range hood fan. We've previously confirmed this with Ventline.

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 5

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 6

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 7

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 8

The two sizes you mentioned are pretty similar and fit many of the same 15 inch wheels. The 205/75-15 fits rim widths of 5 inch to 6 inch whereas the 225/75-15 fits widths that are 5 inch to 6-1/2 inch. The 205 is 27.1 inches tall and the 225 is 28.4…

view full answer...

Answer 9

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 10

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 11

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 12

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Replacement Fan Motor For Kinmore Vent # RS-385 PHC2-171BVDO218-00

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching