Does Trailer valet JXC Trailer jack TV94VR Have A Triangular Or Circular Mounting Plate?

Question

Question:

Does it come with a Cirlce mounting plate or a triangle mounting plate? In the pictures it shows both. Was seeing if I could mount the crank on it side instead of by the tailgate. I would like to mount it like the one in the picture.

asked by: Chris

0

Expert Reply:

The Trailer Valet JXC Trailer Jack w/ Footplate and Drill Powered Option - A-Frame - Sidewind - 5K # TV94FR you were looking at uses a round mounting plate, and can be install with any of the points of the triangular bolt pattern pointing forward to give you the most clearance options based on what is installed on your trailer, or to give you more tail gate clearance.

I included a video of the # TV94FR being installed for you to take a look at.

expert reply by: Samuel C

0

Answer 1

The ALKO 4,400 lb axles use the same bearing sizes as the standard 3,500 lb alxes. If you want USA made bearings, I recommend the Bearing Kit #TMK52VR. This kit comes with the Timken brand bearings which are all made here in the USA.

view full answer...

Answer 2

If your trailer has 7 wires running all the way back to the brakes, then yes, you can tap into the existing wiring. Each of your new brakes will have two wires for the brake magnet. One wire is for 12 volt power to the brake magnets and the other…

view full answer...

Answer 3

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 4

You are going to want either our Bearing Kit #BK2-100 or the Timken Kit #TMK52VR. Both of these kits will give you the inner/outer bearings and races along with a grease seal and cotter pin/D-washer for one hub. You always want to replace the race…

view full answer...

Answer 5

The Kodiak 10" Hub-and-Rotor Assembly #KHR10D matches the TDE 46245 that you currently have. The hub has a disc rotor and 5 on 4-1/2" bolt pattern. The Hub Bearing Kit #BK2-100 contains the races, bearings and grease seal for you to be able…

view full answer...

Answer 6

The correct bearing kit for a Dexter 4,400 lbs axle is item #BK2-100. The Dexter 4,400 lbs axles use the same bearings and seals as a Lippert 3,500 lbs axles. This kit includes inner bearing item #L68149, inner race item #L68111, outer bearing item…

view full answer...

Answer 7

Hi Jayme, Thanks for that info and there is a bearing kit with the L44649 and L68149 bearings you need; the correct kit is the following: - Hub Bearing Kit #BK2-100 This comes with both of those bearings as well as their accompanying races, the…

view full answer...

Answer 8

In order to find if the Dexter 10" Hub-and-Rotor Assembly #K08-435-05 will fit your 2000 620 Ranger boat trailer you will need some additional information. This assembly is designed to fit a 3,500 lb axle with the standard #L68149 inner and…

view full answer...

Answer 9

Hello Gabe thanks for your question. Our records indicate that the 2017 Jayco Jay Feather 16XRB uses a 3,500 lb axle. This means it will have the Inner Bearing #L68149 and Outer Bearing #L44649 which is very much standard. If you need to repack the…

view full answer...

Answer 10

There is no specific torque rating for the castle nut that holds your hub in place. We recommend tightening the castle nut down until it stops, and then backing it off to the next notch wheel the tang washer will fit into the castle nut. Over…

view full answer...

Answer 11

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 12

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Does Trailer valet JXC Trailer jack TV94VR Have A Triangular Or Circular Mounting Plate?

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching