What Are the Dimensions of the Single Axle Trailer Fender

Question

Question:

How to measure for trailer fender. Height, do i need to measure height of backing plate? do i measure across entire fender radius for length or inside lip to tip?

asked by: Ronald H

1

Helpful Expert Reply:

The measurements we've provided for the Single Axle Trailer Fender w/ Backing Plate - Steel - 14" to 15" Wheels - Qty 1 # HP36VR were taken from outside edge to outside edge of the bottoms of the fender (32"), from the top of the arch to the floor when sitting flat (15") and the backing plate itself (12").

I've also linked a photo of these dimensions and the review video where Jeff shows these measurements in real time.

expert reply by: Erik B

1

dimensions
(click to enlarge)

Answer 1

Adding larger wheels/tires to a trailer really comes down to fender clearance. The recommended fender clearance is about 4" from the top of the tire to the bottom of the fender and then about 1" from the tire to the inside of the frame. The…

view full answer...

Answer 2

I sure can Steven, and congrats on the new SUV. To add a hitch to your new 2026 Toyota RAV4 Hybrid, I recommend our etrailer item #e84ZV. This is a custom fit class III hitch that has a 2" receiver. The 2" receiver will give you the most…

view full answer...

Answer 3

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 4

I can understand that if your boat is loaded on the trailer, you don't want to remove one of the wheels to measure the fenders. Measuring a fender with the tire still mounted can be tricky, but it's not impossible. I've provided a diagram…

view full answer...

Answer 5

The closest thing we have in those dimensions is the Single Axle Trailer Fender for Boat Trailers item #HP48VR. It measures 9" Wide x 32" long x 14" tall. You can weld the fender onto your trailer or use the Mounting Brackets for…

view full answer...

Answer 6

Hey Stephen! The Coleman-Mach Mach-C Everest #CM35MR is a complete system so it comes with everything you need to replace an Advent Air AC135. Complete replacement is required since you're moving from an R410A to an R32 system. This works with…

view full answer...

Answer 7

Thanks for the pictures Brian. Yes, you are correct the Replacement Inner Member for Dexter DX7.5L Actuator item #DX99FR will replace your UFP A-70 surge brake actuator. The A-"number" was for the weight capacity of the coupler; an A-60 was…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

What Are the Dimensions of the Single Axle Trailer Fender

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching