Will the Bulkhead Seal For My BAK Revolver X4s Adhere to a Spray In Bed Liner

Question

Question:

Will the bulkhead seal that comes with the product work with a spray-in bedliner? I have a 2021 Sierra and I just got the cover in the mail but didnt consider that the spray-in bedliner could present an issue until I began the install process.

asked by: Kevin J

0

Expert Reply:

Yes. The bulkhead seal # PARTS-326A0005 that is included will adhere to a spray-on bed liner and although it does work in most cases, I checked with Bak and they recommend using the thicker 3/8" seal # PARTS-326A0004 as the seal to use on spray-on bed liners for the BAK Flip series covers and Revolver series covers.

expert reply by: Erik B

0

Answer 1

The product page you linked to is Replacement Locking Block Kit for BAK Revolver X2 Hard Truck Bed Tonneau Covers, #PARTS-356A0015. The plastic pieces in this kit are identified to insert into ends of aluminum slats on the BAK Revolver X2 to hold and…

view full answer...

Answer 2

Yes. This seal will adhere to a spray-on bed liner and although the #PARTS-326A0005 can be used, I checked with Bak and they recommend using the thicker 3/8" seal #PARTS-326A0004 as the seal to use on spray-on bed liners for the BAK Flip series…

view full answer...

Answer 3

The bulkhead seals on tonneau covers are thankfully pretty universal and there are a ton out them to choose from. I like the Replacement Bulkhead Seal for BAKFlip Truck Bed Tonneau Covers part #PARTS-326A0004 because it's very thick at 3/8"…

view full answer...

Answer 4

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 5

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 6

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 7

Yes, the puck system used on the 2016-2019 Chevy/GMC trucks is different than the pucks used on the 2020 and newer trucks. So you would need a 5th wheel like the B&W Companion #BWRVK3710 for your 2020 GMC Sierra 3500 with an 8' Bed. If you…

view full answer...

Answer 8

Hey Steve, The AirLift airbags with internal jounce bumpers are not able to be added to a system without so you would need to get a whole new system. With that said the system with the internal jounce bumpers is going to create a much rougher ride…

view full answer...

Answer 9

Hi Richard! From the top of the shank to the lowest part where the tri-ball sits on the #BWTS20067BMP is 11.125". If you have the balls at max drop with the tallest one hanging down that would be 12.5". We recommend at least 11" of…

view full answer...

Answer 10

The best set of air bags for your 2024 Chevy Silverado 2500, that are compatible with an in bed hitch, are the Firestone Ride-Rite Air Helper Springs item #F2613. These air bags have a 5,000 lbs capacity that will level out the rear end of your…

view full answer...

Answer 11

Hey Scott! The correct bearing kit for your Dexter 6k axle is the Bearing Kit, 15123/ 25580 Bearings, 10-36 Seal #BK3-100. If you want the Dexter version it is the #DX26ER. What kind of trailer do you have?

view full answer...

Answer 12

Hi Curtis! We have you covered! Pun intended. ^___^ What you are looking for are the following parts: Pace Edwards Full-Metal JackRabbit Retractable Hard Tonneau Cover w Explorer Rails - Aluminum #PE36CV Pace Edwards Contractor Rig Rack Truck Bed…

view full answer...

Will the Bulkhead Seal For My BAK Revolver X4s Adhere to a Spray In Bed Liner

Continue Researching