Do the Timbren Silent Ride Suspension Systems Require a Crossmember

Question

Question:

Does this particular Timbren system also require the 2 inch square cross tube. The product pictures do not show the needed brackets, but it is mentioned in the video transcript.

asked by: Phil B

0

Expert Reply:

Yes, the Timbren Silent Ride Suspension Systems like part # TSR2000S03 require a crossmember installed between driver and passenger side. The crossmembers is needed to add additional support. It will be welded to the back of the flange which you can see in the attached photo.

expert reply by: Conner L

0

Timbren Silent Ride Single Axle Crossmember Install Photo
(click to enlarge)

Answer 1

Due to the light weight of your trailer and boat I recommend looking at the Timbren Silent Ride Suspension for Single Axle Trailers. There are a few kits available based on the dimensions of your axle tube. This suspension is superior to leaf springs…

view full answer...

Answer 2

Hey Roshun, thanks for reaching out. You’re correct that bearings are unique and need to be an exact size. The majority of trailers use standard bearing sizes, but Harbor Freight tends to do their own thing when it comes to bearings and axle setups.…

view full answer...

Answer 3

That is correct Robert. Your old saddles or spring hangers are most likely going to be in the way so you'll have to remove them and then grind down the welds to install the Timbren Silent Ride Suspension item #TSR2000S04. You'll want to get…

view full answer...

Answer 4

The part #TSR2000S03 that we offer is for the pair you see in the picture I attached.

view full answer...

Answer 5

The Timbren Silent Ride Suspension for Single Axle Trailers w/ 2-3/8" Round Axles - 2,000 lbs #TSR2000S03 that you referenced has an axle capacity of 2,000 lbs as a pair. Or individually each side would have a capacity of 1,000 lbs.

view full answer...

Answer 6

You will need to use the Roadmaster Comfort Ride Leaf Spring Suspension Kit w/ Shocks #RM-2460-2580 for upgrading the suspension on your 2019 Crossroads Redwood 3951WB Fifth Wheel Camper. This kit is rated for your 8,000lb axle and the springs have…

view full answer...

Answer 7

Hey Jerald! I can't say I have heard of anyone adding the Timbren Silent Ride Suspension #TSR14KT01 (33" axle spacing) or #TSR14K35T01 (35" axle spacing) to their Grand Design but I'm sure some people have done it. This wouldn't…

view full answer...

Answer 8

You'd be best off tailoring the suspension to the maximum weight you're planning on carrying. If you'll be carrying around 1100 lbs typically, I'd recommend going with a 2K axle/suspension. A one inch spindle is typically used on a 2K…

view full answer...

Answer 9

For your trailer we have the Timbren Axle-Less Trailer Suspension System #ASR2000S02 that has a 2,000 pound weight capacity and a hub face dimension of right at 6 inches (see attached image). This particular assembly does not include idler hubs but…

view full answer...

Answer 10

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 11

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 12

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Do the Timbren Silent Ride Suspension Systems Require a Crossmember

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching