Which A-Frame Trailer Jack Sticks Up The Least From The Mounting Flange On Coupler?
Updated 04/23/2021 | Published 04/22/2021
Products Featured in This Question
Question:
whats the shortest jack you have from top plate to handle crank. Im looking for side crank option
asked by: Eric G
Expert Reply:
The shortest A-Frame trailer jack measured from the top of the mounting flange to the top of the jack is the Bulldog Round, A-Frame Jack w/ External Gearbox - Sidewind - 13" Lift - 2,000 lbs # BD155157. The crank on this jack is below the top of the jack, so in this case the highest point is the top of the jack itself.
This jack measures 13" from the top of the mounting plate to the top of the jack as shown in the included diagram, and will give you the most clearance to be open your tailgate. To the point where the crank goes into the jack would be 12".
If this is still to tall to give you the clearance you need, using an extended ball mount like the Brophy Ball Mount for 2" Hitch - 3/4" Rise, 2" Drop - 13-1/4" Long - 10,000 lbs # BH20 which will extend the distance between your vehicle and trailer to allow you to open a tail gate without it hitting the jack.
I included a videos of both products mentioned for you to take a look at.
(click to enlarge)
Product Page this Question was Asked From
Bulldog Round, A-Frame Jack w/ External Gearbox - Sidewind - 13" Lift - 2,000 lbs
- Trailer Jack
- Enclosed Trailer
- Utility Trailer
- A-Frame Jacks
- Standard Grade
- 1001 - 2000 lbs
- Manual Jack
- 13 Inch Lift
- Bolt-On
- Weld-On
- No Wheel or Foot
- Bulldog
more information >
Featured Help Information
Miscellaneous Media
Continue Researching
- Shop: Replacement 1-1/4" Drop Head Assembly for Lippert Through Frame Slide-Out - Adjustable
- Shop: Replacement 1-1/4" Drop Head Assembly for Lippert Through Frame Slide-Out - Fixed
- Video: Replacement 1-1/4" Drop Head Assembly for Lippert Through Frame Slide-Out Spec Review
- Video: Feature Review Replacement 1-1/4" Drop Head Assembly for Lippert Through Frame Slide-Out
- Q&A: How Many Wear Pads Are Normally Used in Lippert Slide Out
- Q&A: How To Get To the Holes To Install the Lippert Components Universal Slide Out Wear Pad
- Q&A: Installation of Lippert Components Universal Slide Out Wear Pads
- Q&A: Lippert Wear Tabs Functionality
- Q&A: Determining The Correct Replacement Slide Out Gear Packs For A 2010 Dutchmen Grand Junction
- Q&A: Troubleshooting A Slide Out Box That Stops Before Fully Sealing Closed
- Search Results: rv slide out parts
- Search Results: lippert hydraulic slide~out systems rv slide out parts
- Shop: Replacement Bracket Kit for pre-2019 Solera RV Slide-Out Awnings - Black
- Shop: Replacement Standard Triple Rack Repair Kit for Lippert RV In-Wall Slide-Outs - Fixed Side
- Shop: Lippert Universal Slide Out Wear Pad
- Search Results: slideout roller
- Video: Review of Lippert Components Slide Out Replacement Dual Rack Kit - LC26VR
- Shop: Trailer Hitch
- Shop: Rubber Wiper Seal with Bulb for RV Slide Out - 3/16" Flange - 40' Long x 2-7/8" Tall
- Video: Rubber Wiper Seal with Track for RV Slide Out Feature Review
- Shop: Trailer Wiring
- Search Results: rv air conditioners
- Shop: Rubber Wiper Seal with Track for RV Slide Out - Stick On - 15' Long x 3-3/4" Wide
- Shop: Suspension Enhancement
- Search Results: rv slide out seals
- Video: Rubber Wiper Seal with Bulb for RV Slide Out Review
- Search Results: lippert rv slide out parts
- Video: Hands-On with the Rubber Wiper Seal and Bulb for RV Slide Out
- Shop: Base Plate for Tow Bar
- Video: Review of Lippert Components RV Exterior Parts - Dual Rack Repair Kit for In-Wall Slide-Out - LC84FR
on Camper Jacks
