Where Are the Replacement Anti-Rattle Springs for Dexter Disc Brake Pads Installed

Question

Question:

how to install correctly

asked by: ALAN

0

Expert Reply:

The Replacement Anti-Rattle Spring for Dexter Disc Brake Pads - 10,000 - 12,000 lbs # BP18-115 is designed to be installed between the two brake pads. I've linked a diagram that shows this as part 7.

expert reply by: Erik B

0

exploded diagram of disc brake assembly
(click to enlarge)

Answer 1

The Replacement O-Ring for Dexter Axle 10K and 12K Disc Brakes part #010-062-00 install on the brake caliper guide bolts between the brake pads as shown in the photo below.

view full answer...

Answer 2

You can still bleed the trailer brakes without a compatible brake controller. But you cannot use the Primus brake controller because it will not work sufficiently enough to properly bleed the trailer brakes. What you will need to do is use a 12 volt…

view full answer...

Answer 3

You could certainly use Opti-Brite LED work light #TLL48FB on your horse trailer and put it on a switch but having it wired into the running light circuit could have some unintended issues. Specifically, if you forgot to turn the switch off and drove…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 9

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 10

Hey Doug! The Firestone Ride-Rite Air Helper Springs #F35FV are the right kit for your 2026 Ford F-350 FX4 dually. However, you will need to measure to be sure it fits. The distance from the top of your rear axle to the top of the jounce bump stop…

view full answer...

Answer 11

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 12

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Where Are the Replacement Anti-Rattle Springs for Dexter Disc Brake Pads Installed

Product Page this Question was Asked From

Continue Researching