Lifting a Fifth Wheel to Fit a New and Taller Truck
Updated 04/14/2021 | Published 04/09/2021
Products Featured in This Question
Question:
I’m already spring over axle... My trailer has what Lippert refers to as “boot” hangers on the front and rear ends of the springs. These have available holes to the springs 2” raising the trailer. The middle hanger is square with no additional holes. Do you have a product to lower just the equalizer by the same 2”? I’d rather not pay for an entire kit if I only need to extend two of the six mounting locations. Picture attached.
asked by: Ken C
Expert Reply:
I have been in contact with Lippert, and I was able to get the individual brackets # LC84PJ added to our site. These will be direct replacements for the Lippert LC407131. As you are only needing these for the center hangers, you will need four of these to get you up and running.
Product Page this Question was Asked From
Correct Track Trailer Alignment and Lift Kit - Single Axle
- Trailer Suspension Parts
- Alignment and Lift Kits
- Boat Trailer
- Camper
- Car Hauler
- Snowmobile Trailer
- Utility Trailer
- Double Eye Springs
- Single Axle
- RV Ride Control
more information >
Featured Help Information
Instructions
Continue Researching
- Search Results: never fail bushings
- Search Results: correct track
- Search Results: morryde cre3000
- Video: Installing the MORryde AllTrek 4000 Equalizers for Tandem Axle Trailers on a 2025 Grand Design Momen
- Search Results: bushings trailer suspension parts
- Search Results: bronze bushing trailer leaf springs
- Search Results: never fail bushing
- Video: MORryde Tandem Axle Trailer Rubber Equalizers Installation - 2009 Keystone Montana Mountaineer Fifth
- Video: MORryde X-Factor Crossmember Installation - 2020 Grand Design Momentum 5W Toy Hauler
- Video: Breaking Down the MORryde ALLTREK 4000 Shock Absorbing Equalizers for Tandem Axle Trailers
- Video: Comprehensive Review: Suspension Bushing
- Video: Complete Breakdown of the Bronze Bushing
- Q&A: Will Replacing MORryde CRE3000 Equalizers With The AllTrek 4000 Affect Ride Height
- Q&A: Best Shock Absorbing Suspension Equalizers
- Q&A: Will MORryde X-Factor Crossmember Work With AllTrek 4000
- Shop: Dexter Bronze Bushings - Qty 4
- Search Results: axle hanger
- Shop: Replacement Lippert Components Correct Track Axle Hanger - Qty 1
- Shop: Bronze Bushing - 9/16" Inner Diameter, 11/16" Outer Diameter - 1-3/4" Long - Qty 1
- Video: Let’s Check Out the Dexter Bronze Bushings
- Q&A: Bushing Recommendation for a Camper Trailer Leaf Spring
- Shop: Replacement Wet Shoulder Bolt - Equa-Flex Tandem Axle Suspension - 9/16" x 3-3/8" - Qty 1
- Shop: Roadmaster Comfort Ride Leaf Spring Suspension Kit w/ Shock Absorbers - Tandem 7K Trailer Axles
- Shop: MORryde AllTrek 4000 Equalizers for Tandem Axle Trailers - 35" Wheelbase
- Shop: MORryde Shock Absorbing Suspension Equalizers for Tandem Axle Trailers w/ 35" Wheelbase - 8K
- Q&A: Does Lippert Lift Kit LC407131 Need Replacement Part # LC84PJ
- Q&A: What Size Bolt to Use with Correct Track Hanger
- Q&A: Lug Nut Torque Chart for Trailer Wheels
- Article: Trailer Wiring Diagrams
- Shop: Trailer Hitch
