Height of Curt Class III Hitch Receiver, Part # C13068, When Installed on a 2007 Honda Odyssey

Question

Question:

Hello, I see on your installation video for the Draw-Tite Class III that the distance from the top of the receiver to the floor is 12 3/4. But the Curt Class III video does not have a similar measurement. I was wondering if you knew what that height is for the Curt. I prefer the bolt pattern on the Draw-Tite, but will go for the Curt if it offers higher ground clearance. Thanks!

asked by: Paul

0

Expert Reply:

For the video on the Curt Class III hitch receiver for 2007 Honda Odyssey, Part # C13068, as you noted
we did not happen to include the measurement of the distance from the ground to the top of the installed receiver, as we did for the Draw-Tite # 75270.

However, since we have both parts in stock I visited the warehouse and took measurements that allow me to determine what the approximate after-installation hitch height will be for the Curt. Since both hitch receivers mount to the same frame members on the vehicle, by measuring the different distances from the mounting flanges to the tops of the receiver tubes, and using the known measurement for the Draw-Tite, we can make a determination of the receiver height on the Curt hitch, part # C13068, after installation on your Odyssey.

Based on my measurements of the two hitches, the Curt receiver, part # C13068, will sit only very slightly higher off the ground - about 3/4 inch higher.

Do note that these height measurements are subject to several variables, such as the tread depth on your tires, their inflation pressure and the cargo/passenger load in the vehicle.

Please also note that both hitch receivers require you to separately purchase a ball mount, hitch ball, pin and clip. For hitch ball I suggest Tow Ready 2-Inch # 19247; for pin and clip you can use part # PC3.

Your choice of ball mount will depend on your trailer coupler height (when level to the ground) relative to the receiver tube on your Odyssey. You can choose either a fixed ball mount that provides the required rise or drop, or an adjustable-height ball mount, a great choice if you will tow more than one trailer or tow with more than one vehicle. I have also linked an article that offers guidance on selecting a ball mount.

I will be happy to recommend any other towing items you might need, such as a trailer brake controller and vehicle wiring harness, if you wish.

expert reply by: Adam R

0

Answer 1

When we installed the etrailer brand #e98862 hitch on a 2011 Honda Odyssey, we found that the receiver height was 14 inches, measured from the ground to the inside top of the receiver tube. The correct ball mount will depend on the coupler height of…

view full answer...

Answer 2

Hey Tyler, those are a lot of great questions, and I am happy to help. According to the online manual, a 2007 Acura RDX can tow up to 1,500 lbs. Meaning you can definitely pull small trailers as long as you stay under 1,500 lbs total. Your best…

view full answer...

Answer 3

I recommend the etrailer Trailer Hitch Receiver #e28AR for your 2022 Kia Sorento X-Line AWD. This receiver is confirmed to fit all trim levels of your 2022 Kia Sorento. The spare tire can be retained in its original location with this receiver. The…

view full answer...

Answer 4

I have a way better hitch for you but the frame on your 2012 Kia Sedona is not wide enough for the Curt Trailer Hitch Receiver item #C13900. Instead you will want the Draw-Tite Max-Frame Trailer Hitch item #75421. This hitch is custom fit and bolts…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

The primary difference is a matter of numbers. When installed, the Draw-Tite Class III #76025 will sit so the inside top edge of the receiver tube sits about 13 inches above the ground, and the receiver tube will sit under the bumper so that the…

view full answer...

Answer 7

From what little I was able to learn about the VelociRAX 5 bike rack on their website, the rack is compatible with a 2 inch hitch that has a tongue weight capacity of at least 500 lbs, and the Draw-Tite #75270 Class III hitch meets both those…

view full answer...

Answer 8

Yes, it will Terry and congrats on the new SUV. The Curt Trailer Hitch item #C12169 has been confirmed to fit the 2026 Honda CR-V Hybrid Touring Sport. This is a custom fit class II hitch with a 1-1/4" receiver that bolts to your Honda with…

view full answer...

Answer 9

Curt decided not to design hitch #C13068 to account for those welded on pieces you referenced in order to maximize the size of the side hitch brackets. As to why they chose to go with a 5 bolt design I can't say. The Draw-Tite hitch #75270 sounds…

view full answer...

Answer 10

For a hitch with a high enough tongue weight capacity you will need the Draw-Tite Max-Frame Trailer Hitch Receiver #75270. Although the #e98862 does have a max tongue weight of 500 lbs with weight distribution, this would require a weight…

view full answer...

Answer 11

For your 2017 Honda Odyssey the Draw Tite hitch part #76025 is a great option to tow with. It has a concealed crosstube too so that it's not overly visible. You will need to start with a 4-way (if you do not have one). For that you would want the…

view full answer...

Answer 12

We have had the chance to install the Curt Trailer Hitch Receiver #C13068 on a few Honda Odyssesys like your 2007 model and have found that the hitch will sit any where from 12-1/2 inches to 13 inches from the ground. To help you pick out the correct…

view full answer...

Height of Curt Class III Hitch Receiver, Part # C13068, When Installed on a 2007 Honda Odyssey

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching