Replacement Clearance Light Assembly, Red Lens, And Amber Lens For Light Stamped SAE-A-P2-83

Question

Question:

Looking for clearance light assy mounting base , bulb , bulb socket and wires and amber and red lens. Mounting base has AFp2 -58-59 imprinted on it ,lens has sae-a-p2-83 imprinted red lens once I get the part numbers. I will order 5 red lens and 1 amber lens and I will need one complete assembly with amber lens , replacement for a missing assy.

asked by: Thomas O

0

Expert Reply:

Based on the sae-a-p2-83 you found stamped on your current lens I was able to verify that you have the Bargman #59 Series clearance lights.

There is no longer a replacement lens available so you'll need complete assembly, the Bargman Trailer Clearance or Side Marker Light w/ Reflector - Incandescent - White Base - Amber Lens # 30-59-002.

expert reply by: Samuel C

0

Answer 1

Trailer tires should be inflated to the maximum psi indicated on the tire. If your tires read 50 psi then that is what you will want to inflate them to. The trailer tires cannot reach their capacity rating unless inflated to the maximum. Trailer…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 5

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 6

Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…

view full answer...

Answer 7

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 8

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 9

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 10

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 11

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 12

Trailer wheel bearings are specific to the spindle that is installed on the axle that is on your trailer. You will need to safely support the trailer, remove the wheel and tire, remove the grease cap, remove the cotter pin and washer that secures the…

view full answer...

Replacement Clearance Light Assembly, Red Lens, And Amber Lens For Light Stamped SAE-A-P2-83

Featured Help Information

Miscellaneous Media

Continue Researching