Distance from Pin Hole To Bottom of Plate on Brophy Stake Pocket Tie-Down Anchors

Question

Question:

I have a question about PK-SPTD. What is the measurement from the pin hole, to the bottom of the steel? I have a trailer where one set of stake pockets are impeded by the frame below it, so I have short clearance.

asked by: Andrew S

0

Expert Reply:

The distance from the top of the pin hole to the bottom of the steel plate for the Stake Pocket Tie-Down Anchors part # PK-SPTD is 1-3/4" which you can see in the attached photo.

expert reply by: Conner L

0

Brophy Camper Tie Down Dimensions
(click to enlarge)

Answer 1

With the Stake Pocket Tie-Down Anchors #PK-SPTD there are two ways this can be installed. The more permanent method which requires you to use the nuts on the pin that runs through it which holds it tight and prevents movement. Or using the cotter pin…

view full answer...

Answer 2

There is a TorkLift SuperHitch that fits your 2012 Ram 3500 with a factory hitch that is welded on, though it is a different part number than the one you mentioned. There are two options for a TorkLift SuperHitch for your truck, one with a 2 inch…

view full answer...

Answer 3

Based on your picture the linkage from the frame to the sway bar would be in the way for Curt trailer hitch #C15409. But not to worry because there is a hitch that accounts for a Hellwig sway bar for a 2003 Dodge Ram 2500 with factory hitch. It is…

view full answer...

Answer 4

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 5

In regards to the TorkLift Custom Frame-Mounted Camper Tie-Downs, these can be used with either the factory trailer hitch or a TorkLift Trailer Hitch Receiver. That said, the rear tie downs are specific to the hitch so if you have a rear tie down…

view full answer...

Answer 6

Since your factory hitch is bolted on and not welded on the correct Torklift hitch is the #TLD1102 and not the part.

view full answer...

Answer 7

Good morning to you as well! I would be happy to Anthony and congrats on your new truck! To flat tow your 2025 Ford Bronco with the Ford Performance Heavy Duty Modular Front Bumper you will need the following parts: Tow Bar and Safety Chains - Curt…

view full answer...

Answer 8

The Dexter DX7.5 Drop-N-Go Brake Actuator part #099-175-20 is designed for use only with a 2" hitch ball and the latch must be seated fully for the safety pin to be inserted. Therefore, I recommend making sure you have the correct ball size and…

view full answer...

Answer 9

The Stake Pocket Tie-Down Anchor - Black Powder Coat - 2-1/4" D-Ring - 4,000 lbs #WFSPDR is made in the United States.

view full answer...

Answer 10

Hey Roger, From under the lip of the Stake Pocket Tie-Down Anchor #BR72ZR to the center of the pinhole is 5-1/8".

view full answer...

Answer 11

Although we don't carry replacement parts for your Reliable brake actuator we do offer a good replacement, the Dexter #DX89FR would be an excellent replacement for your current actuator. You can see a product video for the #DX89FR hydraulic…

view full answer...

Answer 12

There could be a couple reasons this could be happening. One being the hitch ball could be over-sized but I seem to think tightening the lock nut under the wedge will eliminate the need for you to manipulate your hitch ball into the secured position.…

view full answer...

Distance from Pin Hole To Bottom of Plate on Brophy Stake Pocket Tie-Down Anchors

Product Page this Question was Asked From

Continue Researching