Wiring Color Codes for 2006 Chevrolet Silverado

Question

Question:

I have 7 pin receptacle, and a 2006 Chevy Silverado HD crew cab, my truck has a utility bed and there are only wires under the back of my truck. Can you send me a color coded wiring diagram for this truck Thank you

asked by: Anthony R

0

Expert Reply:

While I don't have a wiring diagram for your vehicle, we do have some experience with wiring your vehicle. These are the color codes that GM typically uses and was verified on a 2007 Chevrolet Silverado with factory wiring.

Dark Green - Right Turn/Brake Lights
Yellow - Left Turn/Brake Lights
Brown - Tail Lights
White - Ground
Light Green - Backup Lights
Blue - Electric Brakes
Red/Black - 12 Volt Power

I recommend using a circuit tester, like part # PTW2993 if you do not have one, on your wires to make sure you have the right one for each function. Testing the wires should not take long, but you will want a helper to run through the light functions as you test each of the wires. If you're planning on replacing your socket to make your connections easier when towing, you can use the 7- and 4-Pole Trailer Connector Socket w/ Mounting Bracket # HM40975. This can be used with the wiring harness # PK11998 if needed.

expert reply by: Evangeline M

0

Answer 1

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

Hey Bill, welcome back! Installation of the Roadmaster Front Anti-Sway Bar #RM24RF does require drilling two 1/2" holes to mount the skid plate. These holes are in the crossmember, not in the main frame rails. The included hardware and backing…

view full answer...

Answer 4

Hey David, welcome back. To add a 4-way connector to your 2025 Kia Sportage PHEV, you'll want the Curt item #C99DR. It connects directly behind the rear tail lights and there isn't a way to connect it to a tow package. It will not control a…

view full answer...

Answer 5

Hey Skip, for a new 7-way and 4-way at the rear of your 1999 Ford F-350 you would want the Hopkins part #HM40975 and then for a kit to install a 7-way in the bed of your truck you'd want the part #41157. This part number comes with the harness…

view full answer...

Answer 6

Dan, they won’t. The Dexter 7K ABS brakes #DX69WR / #DX79WR are specifically designed for Dexter Tow Assist axles - the flange offset and ABS tone ring position are unique to Dexter’s design. On Lippert 7K axles, the sensor alignment won’t match, so…

view full answer...

Answer 7

Actually, the P3 now has the upgraded axis accelerometer like the P2. The Tekonsha P3 Trailer Brake Controller #90195, will work with both electric over hydraulic brakes on the trailer as well as electric brakes. It has a menu option on the display…

view full answer...

Answer 8

On a trailer the brake lights and turn signals operate on the same wire/bulb. So, it is odd when the turn signals work, but the brake lights don't. There are 3 possible causes for this that are more likely than any of the other possible causes.…

view full answer...

Answer 9

To cover the easiest things first, make sure that the brake controller output or gain is turned up. If the power is low then the voltage on the blue wire will be low. When testing for voltage make sure to use the manual override and not the brake…

view full answer...

Answer 10

It depends on the year make and model of your vehicle where the brake controller fuse may be located. If you have a factory towing package the fuse is sometimes labeled "trailer tow electric brake". You can check the fuse visually to see if…

view full answer...

Answer 11

I'm pretty sure that's to wire up a third brake light on a camper shell. To know for sure, take a circuit tester, like our part #PTW2993, and test that wire while applying the truck's brakes. If I'm correct it's a dedicated brake…

view full answer...

Answer 12

The factory plug is located above the spare tire on your 2006 Chevy Silverado. I have included a picture of what it looks like and where it is located. You will probably have to lower the spare for easy access to the plug. The tow package wires will…

view full answer...