Can Jack-It 2 Bike Rack Face Towards Vehicle

Question

Question:

When I connect the Jack-It to my trailer, there is not enough room to place a bike on the inside, between the RV window and the rack. Can the Jack-It be turned around so that the wing is away from they RV, towards my SUV and still work?

asked by: Michael T

0

Expert Reply:

It is possible to use the Jack-It 2 Bike Rack for A-Frame Trailers # LGA55VR with the bikes facing your vehicle. That said, we do have to mention it is not recommended because of potential turning clearance issues with the bikes possibly coming into contact with your tow vehicle.

expert reply by: Kyle S

0

Answer 1

Welcome back Larry! The answer to your question entirely depends on which Jack-It bike rack you have. If yours is the Lets Go Aero Jack-It PLUS item #LGA47ZR or Jack-It Pro 2 item #LGA55VR, then the answer is yes. From the top of the mounting plate…

view full answer...

Answer 2

Since you only have 2.5 inches of available space on the frame of your a-frame trailer the Swagman part #S80503 won't work BUT I have a great solution instead. Check out the Jack-It 2 Bike Rack for A-Frame Trailers #LGA55VR. This attaches between…

view full answer...

Answer 3

The distance from the top of the motor housing down to the mounting plate for the Ultra-Fab Electric A-Frame Jack #UF38-944014 is 18 inches. I have attached a photo of the jack that shows the measurement you asked about.

view full answer...

Answer 4

On the Ultra-Fab A-frame trailer jack #UF38-944037 from the top of the mounting plate to the bottom of the gear box it is 14-7/8 inches. I have included a picture showing several external measurements for this jack.

view full answer...

Answer 5

Hey Byron, thanks for writing in, and the mounting flange is 5.3" (or 5-5/16") on the Phoenix Electric Trailer Jack #UF38-944040. You made an awesome choice here with the Phoenix as it's as good as it gets for an A-frame jack. The thing…

view full answer...

Answer 6

At right you will find a link to all of our powered A-frame jacks. These vary in weight capacity, installation method and lift height. I checked the dimensions of many of these and based on the photo I have linked, the Stromberg Carlson #JET-2500…

view full answer...

Answer 7

There are a few possible reasons why your electric A-frame jack is extending fine but you are having trouble retracting. If the motor is not running at all when you push retract on the jack, the switch itself is likely the issue and it just needs to…

view full answer...

Answer 8

Hey Brian, There is not an adapter or any way to use the TopShelf for Yakima EXO SwingBase #Y94VR in a vertical 2 inch receiver. The TopShelf does require you to use the Yakima EXO SwingBase Swing Away Hitch Extender #Y34VR. If you're looking for…

view full answer...

Answer 9

Hi Dan; what kind of tonneau cover do you have? Does it have rails? If you have rails with T-slots on there now you can use a truck bed rack like the Yakima OutPost #Y01152-5855. Does your tonneau cover mount inside the bed rails or on top? What kind…

view full answer...

Answer 10

I do have a way for you to transport all 5 bikes on your travel trailer, but the largest bike rack size that has been tested and approved for travel trailer hitch use is 4 bikes. If you want to go this route then I highly recommend using the Yakima…

view full answer...

Answer 11

The pre-wiring of Furrion pre-wired RVs is basically just two wires as well as the Voyager harness like part #PSVCWVCMS130AP. One wire is the power wire which is the running light circuit and then the other is the ground so it really would just be a…

view full answer...

Answer 12

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Can Jack-It 2 Bike Rack Face Towards Vehicle

Product Page this Question was Asked From

Continue Researching