Correct Backup Camera for 2021 Grand Design Imagine Trailer

Question

Question:

I have purchase a 2021 Grand Design Imagine 17MKE travel trailer. IT is supposedly prewired for a backup camera. What is the proper camera to purchase.

asked by: John

1

Helpful Expert Reply:

The 2021 Grand Design Imagine Trailers accept the Furrion Vision S Wireless RV Backup Camera System which is available in a different configurations; part # FOS43TASF for 4.3" or part # FOS05TASF for 5". These are all plug-in-play options.

expert reply by: Conner L

1

Answer 1

I have some measurements for you which will allow you to verify if the Replacement Amber Lens #A44AB will fit your 2023 Grand Design Imagine XLS 17MKE. This lens is 4" long by 1-1/2" tall, see image below. Unfortunately, only Grand Design…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 6

Hey Jeff. There is definitely a correlation between weight and capacity. I've listed the weight of all three of the Power Mountain Tallboy Off-Road Bottle Jacks we have below: Power Mountain Tallboy Off-Road Bottle Jack - 7-15/16" to…

view full answer...

Answer 7

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 8

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 9

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 10

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 11

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 12

Hey Donny! For your Dometic Penguin/Brisk Air 15,000 BTU AC model B59516.711C0-MX, the correct soft start is the #DMC93JF. This is designed for Dometic Brisk II electronic air conditioner units with in-wall thermostats.

view full answer...

Correct Backup Camera for 2021 Grand Design Imagine Trailer

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching