Guide Pin Diameter and Distance Between Holes for Kodiak Disc Brake Kit

Question

Question:

Kodiak 225 caliper. Do you know what the hole dia is for the guide pins and what the spacing is between the two guide holes? Thanks

asked by: Allen

0

Expert Reply:

The Kodiak guide pins like the part # KGBS are .42 inch in diameter. The thread size is M11 x 1.5.

The distance between the guide pin mounting holes is 6 inches.

expert reply by: Jameson C

0

click to enlarge

Answer 1

The Kodiak Disc Brake Caliper part #KDBC250E which is designed for the Kodiak Disc Brake Kit part #K2HR712E will need to be torqued to 40-50 ft. lbs. per the instructions.

view full answer...

Answer 2

The DeeMaxx item #DE86VR won't because of the spacing on the mounting bracket but I have a caliper that will. To replace your Tie Down Engineering 46304 caliper you will need the Kodiak Disc Brake Caliper item #KDBC225DAC.

view full answer...

Answer 3

What you'll want to do is refer to your instructions for the proper torque specs. For example, the instructions for the 5.2K - 6K Kodiak Disc Brake Kit #K2HR526D call for the brake mounting flange to be welded to the spindle and then the caliper…

view full answer...

Answer 4

While there is not a manual or video available for the Kodiak Disc Brake Caliper Rebuild Kit #KDBC225KIT I did find an expanded drawing of the parts of Kodiak Disc Brake Caliper #KDBC225S which should help so you can see how the pieces fit. The…

view full answer...

Answer 5

Hi Brett, are you referring to the guide bolts? We do carry some replacement guide bolts like the #KGBS which are brand and capacity specific. If they aren't Kodiak, Dexter, or DeeMaxx then we probably don't have a replacement part that fits.…

view full answer...

Answer 6

I spoke with my contact at Kodiak regarding the Replacement Mounting Bracket for Kodiak Disc Brake Caliper #KCMB138HRD referenced in your question. He stated that for Grade 5 bolts, you will want to torque to 85 ft lbs. For Grade 8 bolts you will…

view full answer...

Answer 7

Hey Matt, I believe you are looking for a replacement caliper bolt for your Kodiak calipers which we have with the part #KGBS. Does that look correct?

view full answer...

Answer 8

According to the instructions for the Kodiak Disc Brake Kit - 12" Rotor - 6 on 5-1/2 - Stainless Steel - 5,200 lbs to 6,000 lbs #K2R526S the torque spec for the caliper guide bolts is 45-50 foot pounds. I reached out to Kodiak for the mounting…

view full answer...

Answer 9

Your attached photo indicates that you have an 8-lug wheel. The most common axle capacity for an 8 on 6-1/2 wheel bolt pattern is 7,000. If you do have a 7,000-lb capacity axle, your outer bearing will be #14125A, and your grease seal will either be…

view full answer...

Answer 10

We do not have a direct replacement bolt for your Tie Down Engineering 46304 calipers, however if you're able to take a couple quick measurements we can find a replacement bolts for you. For example, the Replacement Guide Bolt for Kodiak Calipers…

view full answer...

Answer 11

I reached out to my contact at Kodiak regarding the Disc Brake Kit #K2R1058D11E and he said the rotor/spacer bolts need to be torqued down to 90 foot pounds and the caliper clip bolts will be torqued down to 45 foot pounds. I have attached a video…

view full answer...

Answer 12

Yes we do. The calipers and brackets for the Kodiak Disc Brake Kit item #K2R35D can be purchased separately. The caliper is item #KDBC225DAC and the brackets are item #KCMB10RD. I have linked a diagram of the bracket for the Kodiak Disc Brake Kit…

view full answer...

Guide Pin Diameter and Distance Between Holes for Kodiak Disc Brake Kit

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching