How Does Trailer Breakaway Kit Battery Charger Item # 20011 Install

Question

Question:

Hi, I received the above item and am ready to install it on my Hopkins Engager Break-Away Kit with LED Charge Indicator. Most of the info Ive found on your site deals with installing the battery charger to a setup that does NOT include the aforementioned battery box with the charge indicator. Since this box has the red, blue and black wires coming from the little circuit board, Im hesitant on making the splice. Do you have an exact wiring diagram and instructions for this setup? Thanks

asked by: Jeff

0

Expert Reply:

The wires of the # 20011 need to install as follows:

Black wire is connected to the vehicle battery to get the charge
Red wire is connected to battery in the breakaway kit on the trailer
Blue wire is connected to the breakaway switch

For more info on how to install this check out the install video link I attached on this page as well.

expert reply by: Jameson C

0

Answer 1

The Trailer Breakaway Kit Battery Charger #20011 is used to charge the breakaway battery on a trailer. The black wire connects to the tow vehicle's battery to get 12V, the red wire connects to the positive terminal on the trailer's breakaway…

view full answer...

Answer 2

Frist you will need a Battery #BRW34FR. This is a deep cycle battery which is designed to be drained and recharged as needed. I recommend using the TorkLift PowerArmor Solar Single Locking Battery Box #TLA7720RS to secure the battery to your off road…

view full answer...

Answer 3

Essentially there isn't a difference but one part number is how you order it from Hopkins if it's in bulk (like we do) or if you are ordering it independently. So if you order the #20011 you'd get the same thing as Hopkins 20007.

view full answer...

Answer 4

The solar panel will keep the battery from draining while sitting but if power is drawn from the battery the solar panel and charger will not be able to charge up the battery. The charger #20011 is designed for small 5 amp hour batteries in breakaway…

view full answer...

Answer 5

I contacted our representative at Hopkins and he informed me that the Trailer Breakaway Kit Battery Charger, part #20011 can charge batteries of different sizes, even large batteries, it will just take a bit longer. He informed me that part #20011…

view full answer...

Answer 6

The Hopkins Trailer Breakaway Kit Battery Charger #20011 has a power output of 2.5 amps according to my tech contact at the manufacturer. It basically gives a maintenance charge to the battery. It is designed for use with the 12 volt 5 amp hour…

view full answer...

Answer 7

The inside dimensions of the #TLA7720RS are about 17 x 8 x 12. I've looked over a few battery sizing charts, and for a typical automotive battery, I couldn't find one that wouldn't fit. The same would go for the marine battery sizes I…

view full answer...

Answer 8

Hey Rebecca! Information is limited and isn't finalized yet from Trailer Valet since the #TV83FR is still a preorder. However, I was able to find that the full height of the jack when it is retracted is 33" from the wheels to the top. I also…

view full answer...

Answer 9

A diode like the part #RM-690 is a great idea but the only issue is that is has a max load of 85 amps. A standard 5,000 lb winch, like the ComeUp DV-5000si #CU645010, will greatly exceed the 85 amp rating of the diode so it would be useless. What you…

view full answer...

Answer 10

You can use a large marine battery to power your winch as well as the breakaway system, people do it all the time. However, it's not the best practice. You can connect the marine battery to the 12-volt accessory feed from the 7-way, but the…

view full answer...

Answer 11

What you'd want is a converter/smart charger like the Progressive Dynamics part #PD4060K which you'll wire your battery, RV service power supply, and fridge and it will allow you to charge the battery and draw from the RV power source when…

view full answer...

Answer 12

While you can add a second battery to power lights, this is going to require a second, 12 volt auxiliary battery; this is the same concept you were thinking of but a breakaway system battery isn't going to have the power or amp hours needed for…

view full answer...

How Does Trailer Breakaway Kit Battery Charger Item # 20011 Install

Featured Help Information

Miscellaneous Media

Continue Researching