Replacement Slide Out Motor Assembly for Power Gear 524120

Question

Question:

Trying to get a good replacement part number so I can order a new slideout motor/ gearbox assembly. Fleetwood part number 524120. I have a 2007 Fleetwood Discovery 39L. It for the forward driver’s side living room slideout. Thanks

asked by: Wayne E

0

Expert Reply:

The correct replacement for your 524120 slide out motor is the Replacement Gear Motor Assembly for Lippert Slide-Out # LC27VR. I confirmed this with my contact at Lippert.

expert reply by: Jon G

0

Answer 1

The correct replacement for your 524120 slide out motor is the Replacement Gear Motor Assembly for Lippert Slide-Out #LC27VR.

view full answer...

Answer 2

The only solution I have is for a complete replacement system. Unfortunately, the Atwood Leveleg system was discontinued so there is not a replacement jack available. For a replacement, I recommend the Lippert Ground Control 3.0 Electric 5th Wheel RV…

view full answer...

Answer 3

I may have a solution for you, but from what I was able to find in my research, the Springlift SL-33-70 was made by Attwood and has been discontinued. It looks like this spring has a 15" extended length and 9.25" compressed length, with a…

view full answer...

Answer 4

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

Thanks for the picture! I checked with Progressive Dynamics the replacement power converter you need for your Parallax Series 7300 Model 7345 is the Replacement Converter for Parallax/Magnetek or WFCO RV Power Centers - 45 Amp item #PD4645V.

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 10

Hey Micah! Pacbrake has actually been around for a long time, more than 60 years. We have had customers ask for these air bags in the past, and we've seen them on vehicles coming in. Until now, Firestone has been the go to since their quality is…

view full answer...

Answer 11

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 12

Both the Roadmaster and Blue Ox tow bars are great options. But if it was my decision to make I would go with the Blue Ox Avail part #BX7420 as we have found that the Blue Ox tow bars are a little easier to connect and disconnect from. Also this tow…

view full answer...

Replacement Slide Out Motor Assembly for Power Gear 524120

Product Page this Question was Asked From

Continue Researching