Is There a Way to Install a Gooseneck Hitch in 2005 Ford F-350 Cab and Chassis Truck

Question

Question:

Hello I have noticed that my 2005 ford f350 cab and chassis is different then the regular truck. I want to make sure that I get the correct kit to install a goose neck plate on it. Whick one should I use? Thank you

asked by: Nicolas O

0

Expert Reply:

You are correct that the cab and chassis models of trucks have a narrower frame width at 34 inches instead of typically around 37 inches so the gooseneck fits are different.

The Curt Flat Plate Gooseneck # C65500 is a multi-fit application that can be used on a cab and chassis truck. Typically, the plate would be placed on top of the flat bed over the rear axle.

You will need to have a shop fabricate rails to be used to provide the under bed bracing in order to reach the maximum 30K lb GTW rating on the plate. Holes would be drilled through the plate, through the bed and into the frame members and the rail kit. At least six 1/2 inch grade 5 bolts need to be used to fasten the plate to the rail kit.

At this time there are no custom fit gooseneck hitches or rails that would fit your vehicle due to it being a cab and chassis.

expert reply by: Jameson C

0

Answer 1

The Reese 15K 5th Wheel Hitch 30049 that you referenced is the same as the Reese 16K 5th Wheel Trailer Hitch part #RP30051 save for the head but they both use the same base, Reese Square Tube Slider for 5th Wheel Trailer Hitch part #RP30048. I am not…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 8

Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…

view full answer...

Answer 9

Hey Doug! The Firestone Ride-Rite Air Helper Springs #F35FV are the right kit for your 2026 Ford F-350 FX4 dually. However, you will need to measure to be sure it fits. The distance from the top of your rear axle to the top of the jounce bump stop…

view full answer...

Answer 10

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 11

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 12

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Is There a Way to Install a Gooseneck Hitch in 2005 Ford F-350 Cab and Chassis Truck

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching