Mounting Hole Locations/Sizes for etrailer Scissor Jack to Fit 2014 Prime Time Avenger

Question

Question:

Will this product fit bolt holes for a primetime avenger 2014 27ft.

asked by: Robert V

0

Expert Reply:

I honestly don't have any bolt hole mounting specs for any travel trailer, like your 2014 Prime Time Avenger, so you'll just need to check out your trailer frame to see if the Scissor Stabilizer Jack # TJSC-24 is compatible with your application.

Attached is a review video as well as a photo showing the dimensions of the bolt hole mounting pattern and sizes for this universal scissor jack.

expert reply by: Jon G

0

click to enlarge

Answer 1

The Ram Scissor Stabilizer Jack #TJSC-24 has a shipping weight of 12 lbs. When you take away a few lbs for the shipping materials that leaves you with about 10 lbs just for the jack itself.

view full answer...

Answer 2

I spoke with the manufacturer and the specs for the screw on the Scissor Stabilizer Jack - 18-3/4" Travel - 2,500 lbs - Qty 1 #TJSC-24 are as follows: TPI: 8 threads per inch Diameter: 5/8" Material: 20Cr Steel

view full answer...

Answer 3

I went out to the warehouse to measure the hole diameter and spacing on the foot (base) of the Ram Scissor Stabilizer Jack - 18-3/4" Travel - 2,500 lbs - Item #TJSC-24. The holes are 1/2 inch in diameter and are spaced 6-13/16 inches apart on…

view full answer...

Answer 4

The Ram Scissor Stabilizer Jack #TJSC-24 that you referenced weighs 12 lbs.

view full answer...

Answer 5

The Econo Porch Trailer Step with Handrail and Landing - Double - 7" Drop/Rise, 20-1/2" Tall #EHS-102-R does not require a stabilizer. It is a strong step with a weight capacity of 350 lbs. I've attached some videos to assist. The…

view full answer...

Answer 6

In regards to the Scissor Stabilizer Jack part #TJSC-24, the slot is not designed to support the frame. I must recommend you attach the two ears to the bottom of the frame as you can see in the attached video. I have also attached for you some…

view full answer...

Answer 7

Hi Marty; to answer your question, the SnapPad SnapJack SJ for RV Scissor Jack Stabilizers #SN65FR will work for your 9,200 lb trailer, yes. The specs aren't actually for the SnapPads themselves (which I know is a bit confusing). The #SN65FR will…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 11

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 12

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Mounting Hole Locations/Sizes for etrailer Scissor Jack to Fit 2014 Prime Time Avenger

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching