How To Determine Correct Trailer Fender Height When Mounting
Updated 05/14/2020 | Published 05/12/2020
Question:
I have a home built trailer with independent torsion suspension and I am looking to purchase fenders. My questions is how do I determine the clearance height inside the fender so the top of the tire does not rub or hit the top inside of the fender? Any information would be helpful. Thank you.
asked by: Bill L
Helpful Expert Reply:
The recommended clearance needed between the trailer fender and trailer tire is 3-4" from the top of the tire to the bottom of the fender. That said, it would be best to mock this up beforehand and see which location works best with your setup. The correct fender will be selected based on the diameter of the wheel. The Single Axle Trailer Fender part # HP79VR
for example is designed for 13" - 14" diameter wheels.
I have attached a full list of fender options below.
Product Page this Question was Asked From
Single Axle Trailer Fender w/ Backing Plate - Steel - 13" to 14" Wheels - Qty 1
- Trailer Fenders
- No Step
- 13 Inch Wheels
- 14 Inch Wheels
- 7-3/4 Inch Wide
- 28 Inch Long
- Steel
- Bolt-On
- Weld-On
- For Single-Axle Trailers
- etrailer
more information >
Featured Help Information
Miscellaneous Media
Continue Researching
- Q&A: Trailer Fender Installation Clearance and Mounting Project
- Video: Breaking Down the Single Axle Trailer Fender w/ Backing Plate
- Search Results: axle
- Q&A: What Happens If you Mix a Radial and Bias Ply Tire on a Trailer
- Q&A: How To Find Replacement Axle for Trailer with 47-1/2" Spring Center
- Q&A: Replacing Harbor Freight Trailer Axle and Mounting on Underside of Leaf Springs
- Q&A: What is Difference Between Trailer Bearings L44649 vs L44643
- Q&A: Replacement Trailer Axle Recommendation for a 4 by 8 Utility Trailer
- Q&A: Upgrading the Axle on 4x8 Trailer
- Shop: Karrier ST175/80R13 Radial Trailer Tire with 13" Galvanized Wheel - 5 on 4-1/2 - Load Range D
- Shop: Loadstar ST175/80D13 Bias Trailer Tire with 13" Galvanized Wheel - 5 on 4-1/2 - Load Range B
- Shop: CE Smith Spindle Axle - Weld on - 1-1/16" Diameter
- Shop: Replacement Trailer Wheel Bearing - L44649 - Qty 1
- Shop: BTR E-Z Lube Spindle for 2,000-lb Trailer Axles - 1-1/4" Diameter
- Shop: Loadstar ST175/80D13 Bias Trailer Tire with 13" Galvanized Wheel - 5 on 4-1/2 - Load Range C
- Shop: Spring Seat for Typical 2,000-lb, Round Trailer Axles with 1-3/4" Diameter - Qty 1
- Search Results: trailer hitch
- Video: Curt T-Connector Vehicle Wiring Harness Review C56040
- Article: Trailer Wiring Diagrams
- Shop: Trailer Hitch
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Search Results: trailer tires and wheels
- Shop: Trailer Wiring
- Video: Inside Look at TowSmart and Oris Hitches with the Manufacturer
- Shop: Suspension Enhancement
- Search Results: trailer wiring
- Article: Wiring Trailer Lights with a 7-Way Plug (It's Easier Than You Think)
- Search Results: trailer lights
- Article: How to Choose the Right Trailer Hitch Class
- Video: Measuring To Choose The Right Trailer Axle
on Trailer Fenders
