Where are Curt Jacks Made and are Any Jacks Made in the USA

Question

Question:

Where is this jack produced?

asked by: Dorman N

0

Expert Reply:

The Curt jack part # C28304 is made in China.

We do have a similar rated and style jack, the Dutton-Lainson part # DL22683, that is made here in the US. This jack has the same 2,000 pound capacity and 15 inches of lift. It's also a weld on jack that swivels just like the Curt.

expert reply by: Charles S

0

Answer 1

Hi George! Yes, the Dexstar Steel Mini Mod Trailer Wheel, Part #AM20242, can fit a 12 inch hub, but the hub size itself isn't what determines whether the wheel will fit. The important thing is that your hub has a 4 on 4 bolt pattern, since…

view full answer...

Answer 2

Hi Ken, The company that owned Bulldog went out of business early this year so we no longer have Bulldog brand items available on the site. The most similar jack I could find compared to the Bulldog 151110 is the Dutton-Lainson Pull Pin, Easy Swivel…

view full answer...

Answer 3

David, check out the SnapPad Donut #SN95FR. This is specifically designed for trailer wheel jacks with a 6"-8" wheel. I really like it over some of the others as it has a hole in the center so to not collect water. It can also be used on…

view full answer...

Answer 4

Hey Gary, it sounds like you might be able to use the Removable Steel Foot with Pin #DL22541 which has an outer diameter of 2" and an inner diameter of 1-3/4". Normally you would just remove a pin and remove the wheel to replace it with…

view full answer...

Answer 5

According to the installation instructions for the Bulldog Top Wind Round, A-Frame Jack, #BD155032, the only maintenance needed is applying a light machine oil to the stem that the handle attaches to. The installation instructions also recommend…

view full answer...

Answer 6

The diameter of the topwind handle on the Curt Jack part #C28304 is 1/2 inch. This is the round metal section that attaches to the crank of the jack and the red knob.

view full answer...

Answer 7

If I am understanding your situation properly you are going to have to have the snap ring mount removed from your trailer and then have the part #C28304 welded in place of it so that you can mount the Curt jack. There isn't a way to adapt the…

view full answer...

Answer 8

The snap ring, part #SNP-RING that holds the etrailer sidewind jack, part #TJB-2002S-B measures 2-inches diameter. If that is the diameter of the snap ring you need for your trailer jack it may work but there is no guarantee since it is designed for…

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 11

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 12

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Where are Curt Jacks Made and are Any Jacks Made in the USA

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching