What Tool For Tightening Bolt on Phoenix USA PXQ2010 Wheel Center Cap

Question

Question:

Recently purchased Phoenix USA Wheel Center Cap - 6-1/2inch Axle Diameter - Center Hole Mount - Right Thread - Rear Item # PXQ2010. What tool/wrench should I purchase to thoroughly tighten the center outside bolt?

asked by: Diane F

0

Expert Reply:

The correct installation tool for the Phoenix USA # PXQ2010 Wheel Center Cap is part # PHX54FR.

expert reply by: Mike L

0

Answer 1

It definitely sounds like you are needing something like Phoenix USA Rear Wheel Center Cap - 8-1/4" Hub Diameter - Center Hole Mount - Right Thread #PXQ2020XL. Just a few things to check to confirm fitment, this fits 10 lug on 285mm pattern and…

view full answer...

Answer 2

As far as a left-threaded or right-threaded cap for your motorhome, right-handed threads run clockwise, and left-handed threads run counterclockwise. The reason for this difference is that some applications of screws can come loose with the motion of…

view full answer...

Answer 3

Even though most threads on bolts use right-handed bolts/nuts, some special scenarios warrant a left-handed thread. When wheel accessories like the Phoenix USA Rear Wheel Center Cap - 8-1/4" Hub Diameter - Center Hole Mount - Left Thread…

view full answer...

Answer 4

You will need either the Phoenix USA Rear Wheel Center Cap Right Hand Thread #PXQ2010XL or Left Hand Thread #PXQ2010L if you have a 6-1/2" wide hub. Otherwise you will need the Right Hand Thread #PXQ2020 or Left Hand Thread #PXQ2020L if you have…

view full answer...

Answer 5

The diameter of the center indention (hole) on the Phoenix USA Baby Moon Hubcap #PXQ1402B is 3" from outside beveled edge to outside beveled edge and 2.7" across the flat surface inside the beveled edges. I have included a picture to help…

view full answer...

Answer 6

The Phoenix USA Wheel Center Cap part #PXPH1843 is a replacement for the Phoenix USA Wheel Center Cap part #PXQ1009 which is for a 6-1/2" diameter axle or the Phoenix USA Wheel Center Cap part #PXQ1020 which is for a 8-1/4" diameter axle.…

view full answer...

Answer 7

The Phoenix USA Wheel Center Cap part #PXQ2010 has right hand threads (threads run clockwise) but that does not mean there is a left and right hand cap. You will need to check the bracket of your existing cap to see if there is a L at the end of…

view full answer...

Answer 8

For a right hand thread you'll need part #PXQ2020XL and for a left hand thread you'll need part #PXQ2020L. Both of these are designed for 8-1/4" hub diameters and a 10 lug pattern.

view full answer...

Answer 9

Manufacturers do not list the parts they use on their RV's so you'll need to measure the bolt pattern and hub size of your current setup to determine the compatibility of the Phoenix USA Rear Wheel Center Cap #PXQ2020XL. The #PXQ2020XL fits a…

view full answer...

Answer 10

Hey Chuck, For that wheel size we offer the Phoenix USA Baby Moon Hubcap #PXQ1402B and #PXQ1401B. These hubcaps are 8-7/8" in diameter and fit a 221mm hub bore with 4-spline hub. They are slightly different in design with one have a smaller…

view full answer...

Answer 11

The Phoenix USA Rear Wheel Center Cap - 8-1/4" Hub Diameter - Center Hole Mount - Right Thread #PXQ2020XL fits the rear motorhome wheels that has a hub diameter of 8-1/4 inches and a bolt pattern of 10 on 285 millimeters. When it comes to the…

view full answer...

Answer 12

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

What Tool For Tightening Bolt on Phoenix USA PXQ2010 Wheel Center Cap

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching