Can this Light Fixture be Shortened

Question

Question:

Can the stem of this light be shortened if wanting to install over dinette table?

asked by: Douglas R

0

Expert Reply:

The Gustafson RV LED Pendant Light part # 277-000451 has a rod that is threaded on both ends to accommodate the nut that holds the pieces together. Shortening it is possible but not an easy task. You would need to disassemble the fixture. Cut the tube down to you desired length. Then you would have to use a tap and die set to replace the threads back on to the rod which is where the difficulty would come in.

expert reply by: Randy B

0

Answer 1

The Gustafson LED pendant light, part #277-000451, is a 12 volt light.

view full answer...

Answer 2

The bulb for the Gustafson 12V RV LED Pendant Light w/ Light Shade #GUS62VR is just below the stem so you would have to completely disassemble the light in order to replace the bulb. The portion inside of the shade that short of looks like the bulb…

view full answer...

Answer 3

I went out to the warehouse to take a look at the Gustafson 12V RV LED Pendant Light w/ Light Shade #277-000456 and tried to disassemble it but they glued the screws in place on it so I wasn't able to take it apart without damaging the light.…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 9

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 10

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 11

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 12

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Can this Light Fixture be Shortened

Product Page this Question was Asked From

Continue Researching