What Is the Length and Diameter of the A-60 Replacement Coupler Pin Kit TK71-764-00

Question

Question:

What is. The size diameter and length length of the pin

asked by: Gary

0

Expert Reply:

The Replacement Coupler Pin Kit for Titan/UFP Brake Actuators part # TK71-764-00 is 3" long x 1/4" diameter. I spoke with Dexter to confirm this for you.

expert reply by: Conner L

0

Answer 1

Hi Robert; the Replacement Coupler Pin Kit for Dexter Brake Actuators #TK71-764-00 is 3" long x 1/4" diameter.

view full answer...

Answer 2

Your TDE model LP7000 surge brake actuator will need to be entirely replaced as the master cylinder is no longer available for it. With this unique style coupler you will need either a Disc #DX63FR or Drum #DX53FR brake actuator which will need to be…

view full answer...

Answer 3

The Replacement Shock Absorber Spring Kit #TK71-758-00 is the correct shock for your UFP Surge Brake Actuator. The picture you included does not specify if it is for a disc or drum brake set, so I have found both for you to choose from. Disc Brake…

view full answer...

Answer 4

Good question, and a 2012 Cadillac Escalade does not have a harness that will allow you to plug in a brake controller, but it does have the wires already run under the dash, regardless of if you have the factory 7-way or not. If you take a look at…

view full answer...

Answer 5

The three most common lug stud sizes for a trailer are 1/2"-20, 9/16"-18, and 5/8"-18. In order to make sure you get the correct lug nuts you need to measure the lug studs on the trailer now as we have no way to look this up for…

view full answer...

Answer 6

The Kenda 5.70-8 Bias Trailer Tire with 8" White Wheel #AM30140 fits 1/2"-20 wheel bolts so you will need a 1/2" lug nut such as the CE Smith #CE11051, though the Offset Spare Tire Carrier #CE27310G.

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 11

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 12

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

What Is the Length and Diameter of the A-60 Replacement Coupler Pin Kit TK71-764-00

Product Page this Question was Asked From

Continue Researching