Can the Length of the TorkLift Camper Anchor Relocation Kit Be Shortened

Question

Question:

I have a 2019 SB Ram Dually. TLA 7004 seems to be the only option available to move the tie downs on the camper to clear the fenders. The kit seems to be too long, can you comment on its install, as none of the holes line up with the camper.

asked by: Michael K

0

Expert Reply:

I spoke with Torklift about the TorkLift Camper Anchor Relocation Kit part # TLA7004 and they informed me that you could easily shorten the length if needed by simply overlapping the pieces of angle iron and then just drilling new holes to secure the two pieces. That said, the overall length of the bracket is 85-5/8" so you may not need to shorten it.

I have emailed the installation instructions for you as well to help clarify any other questions you should have.

expert reply by: Conner L

0

Answer 1

You typically only need them on the front Reid. The HappiJac Extender Bracket for Dual Wheel Chassis Truck Camper Jacks item #HJ54FR are going to give you the necessary clearance to back your dually truck up so you can drop your camper in the bed.…

view full answer...

Answer 2

The Torklift #TLA7004 Camper Anchor Relocation Kit does not require drilling into the camper or the truck. The adapter brackets would be attached to the camper by drilling holes at the location of the original anchor point, as shown in the photo…

view full answer...

Answer 3

I checked with Torklift and they recommend when using #TLD2120 and #TLD3109 on a dually, first measure between the anchor points and if the measurement there is less than 90" you need the TorkLift Camper Anchor Relocation Kit #TLA7004 to…

view full answer...

Answer 4

We do have 6-Pole Square Trailer Wiring Connector Kit (Car and Trailer Ends) #37995 that you can use for your Arctic Fox camper. This is both the male and female ends. But the wires on them are 18 gauge. You could replace the ground and power wires…

view full answer...

Answer 5

Hey Brian, thanks for reaching out. We do offer TorkLift frame mounter camper tie downs for your 2024 Ram 3500 6.4' bed with cab length steps. You will need the following: - TorkLift Camper Tie-Downs - Custom Frame Mount - Front #TLD2141…

view full answer...

Answer 6

The Swing Out Extension Brackets part #LC182496 which are for HappiJac Truck Camper Jacks will add approximately 3-1/2" - 4-1/2" of clearance to the existing jacks per side. This can then be used to determine compatibility. I would…

view full answer...

Answer 7

Hey Jim welcome back. To determine if you need the TorkLift Camper Anchor Relocation Kit item #TLA7004, you'll have to take a measurement. You'll want to measure from the front bumper of your Palomino HS2902 to the center of the rear anchor…

view full answer...

Answer 8

The correct Torklift Camper Tie Downs for your 2022 Ram 3500 would be the part #TLD2141 and #TLR3510 which is also correct for use with the Torklift 30k hitch that fits your truck part #TLD1111-30. Since you have a dually you will also need to…

view full answer...

Answer 9

Hello Ken, thanks for reaching out. Sounds like you are on the right track here because the type of running boards on your truck do dictate which tie downs to use. You are also correct that you will not be able to use the tie downs from your old 2002…

view full answer...

Answer 10

Thanks for all the info on your truck and camper Jack as that makes picking out the tie downs you need for your 2019 Ram 3500 very easy. The tie downs you need are the #TLD2140 for the front and part #TLD3112 for the rear. Since you have a dually…

view full answer...

Answer 11

Hey John, congrats on the new truck. Yes, the Brophy Slide In Camper Tie-Downs - Extra Clearance item #HSAB can be used with your 2026 Ram 3500 dually. What turnbuckles did you use previously with your 2021 Lance 865?

view full answer...

Can the Length of the TorkLift Camper Anchor Relocation Kit Be Shortened

Product Page this Question was Asked From

Continue Researching