Mounting Hole Dimensions and Bolt Hole Dimensions of JIF Winch # 315W2500D

Question

Question:

Would you please provide the mounting hole dimensions size and locations? Thanks

asked by: Jerry Z

0

Expert Reply:

I attached a picture that shows the dimensions of the JIF winch # 315-W2500D as well as another picture that shows the overall dimensions of the jack.

expert reply by: Jameson C

0

click to enlarge

Mark B.

4/27/2020

will this jif 2500 pound winch fit my 1994 ranger r70 sport or have to drill new holes

Reply

Chris R.

4/29/2020

The mounting holes on the JIF Winch # 315-W2500D are pretty standard but I'm not able to track down the pattern on your Ranger Boat Trailer, so I can't verify fitment (without drilling). I would just try to compare the bracket holes on your trailer with the mounting hole dimensions pictured above to determine compatibility.

Reply

Answer 1

I wouldn't hesitate to add the 2-Speed Boat Trailer Winch with 20' Strap - 2,500 lbs #315-W2500D to your 3 inch wide trailer winch post. Many of the boat winch posts are not even that wide. For instance the CE Smith Winch Stand - Galvanized…

view full answer...

Answer 2

The 2-Speed Boat Trailer Winch part #315-W3200D is an excellent upgraded 3,200 lb winch for a boat trailer. In regards to mounting, not all winches use the same pattern so you'd need to compare the dimensions in the photo below to what you have…

view full answer...

Answer 3

The Fulton High-Performance 2-Speed Trailer Winch - Rope or Strap - 2,600 lbs #F142412 does not have the quick disconnect feature. You would need to remove the handle using a wrench or socket. The 2 speeds have a lever change instead of the handle…

view full answer...

Answer 4

The base on 2-Speed Boat Trailer Winch #315-W2500D measures 5-3/4 inches wide by 7-1/8 inches long. I have included a picture showing this for you and a link to a video review on this winch.

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

Hey Patrick, those dimensions don't appear to be anywhere from what I can find. While I can't give you that info, I can say that as long as the bearings fit, and you have a #11 or #12 spindle, then the Dexter Trailer Hub and Drum Assembly…

view full answer...

Answer 8

Trailer wheel bearings are specific to the spindle that is installed on the axle that is on your trailer. You will need to safely support the trailer, remove the wheel and tire, remove the grease cap, remove the cotter pin and washer that secures the…

view full answer...

Answer 9

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 12

Since both a ST145/R12 size tire, like the Kenda Karrier S-Trail #AM10130, and a 5.30-12 size tire, like the Kenda K353 #AM10068, fit a 12 inch wheel, a ST145/R12 size tire can replace a 5.30-12 size tire. Keep in mind that these tires do have…

view full answer...

Mounting Hole Dimensions and Bolt Hole Dimensions of JIF Winch # 315W2500D

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching