What Size Bolts are Used to Install Curt Hitch on 2017 Chevy Traverse

Question

Question:

I have a 2017 Chevy traverse what size are the bolts used for bolt down the tow hitch under the vehicle

asked by: Andrew

0

Expert Reply:

The install hardware that the Curt hitch part # 13424 that you referenced uses is M12-1.75 x 30mm. If you were looking for replace install hardware for this hitch we have that with the part number # RHK. On the product page for this you'd need to enter your hitch part number and then select Curt as the manufacturer for the hitch and you'd be set.

expert reply by: Jameson C

0

Gabe B.

7/1/2020

I’m trying to install this on my 2008 GMC Acadia but the bolts seem to be too thick and don’t screw in. Does it need a smaller bolt?

Chris R.

7/7/2020

It's very likely that the factory weld nuts on the frame rails of your Acadia are just a bit rusted - this is actually a fairly common scenario, so much so that we have an article dedicated to it. I've linked it below. Just let me know if it doesn't help!

Helpful Links

faq-how-to-clean-weld-nuts.aspx

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 3

Hey Jonathon thank you so much for all of that additional information! To haul your bikes behind your class C Sprinter motorhome, while flat towing your Mini, I recommend the Hollywood Racks RV Rider Bike Rack item #HLY64FR and the Roadmaster Dual…

view full answer...

Answer 4

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Answer 5

Congrats on the new motorhome Edward! SnapPad doesn't have the 2026 Allego Red 38 KA in their system so I don't know what size your jack feet are. However, we have a few options that will work with the HWH leveling systems. What you'll…

view full answer...

Answer 6

Hey Claudia, I checked with Curt just now and confirmed that their hitch part #C64DR does fit all models of the 2026 Toyota Corolla Cross which includes the hybrid models so it would work great for you. We also had customers with similar hybrid…

view full answer...

Answer 7

Hey Michael, congrats on the new SUV. The EcoHitch item #EH87CR does not require you to remove the rear bumper assembly when installing. It does require some slight fascia trimming though. You'll have to remove a 2-3/4” deep and 4-1/2” wide…

view full answer...

Answer 8

Hey Kelly! The Curt 13146 fits 2016 - 2022 Honda Pilot. What you need for your 2026 Honda Pilot is the Curt #C22HR. This has a bolt-on installation and does not require any cutting or trimming of the bumper so you won't be modifying the vehicle.…

view full answer...

Answer 9

Hey James, we have the Curt hitch part #C34FR62ZY as a confirmed fit for your 2026 Toyota RAV4. This fits the hybrid and the PHEV versions BUT it's on a bit of a backorder and won't be available for some time. Are you planning on doing some…

view full answer...

What Size Bolts are Used to Install Curt Hitch on 2017 Chevy Traverse

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching