Wheel Lock Nuts for 2020 Cargo Mate Trailer BL58SA

Question

Question:

Hello, I want to buy Wheel Lock Nuts for my 2020 Cargo Mate Trailer: Model BL58SA GVWR = 3000 Wheel Size: 15inch ST205/75R15 Bolt Circle: 5 x 4.5 With the above information, can you tell me what thread size or wheel lock nuts that will fit my trailer? Thank

asked by: WILLIAM B

0

Expert Reply:

Based on the info you listed for your 2020 Cargo Mate Trailer BL58SA you'd have 1/2 inch diameter wheel studs so for wheel locks you'd need # RG01-150.

expert reply by: Jameson C

0

Answer 1

While we don't have anything specifically designed for that you could maybe use the Spring Latch w/ Cover and Holdback #F779-204U234 installed on the ramp which you'd then be able to push the pins up to lock the ramp up from the inside to the…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

To install a Redarc Tow Pro Liberty in your 2023 Toyota Tacoma Sport you will need the following parts: Redarc Tow-Pro Liberty Brake Controller item #RED24FR Plug-and-Play Wiring Harness for Redarc Tow-Pro Trailer Brake Controllers item #RED99FR…

view full answer...

Answer 5

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 6

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 7

Hey Brandon, I would strongly recommend sticking with the Tekonsha RF brake controller part #TK94FR. We know this works really well and it sounds like it worked well for you too. The Curt Echo is not reliable enough for me to really ever recommend it…

view full answer...

Answer 8

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 9

We can get you everything you need for towing with your 2017 Toyota Sienna XLE. By plastic shield, I believe you are referring to the appearance panel underneath the Sienna, and that will have to trimmed a bit in each of the hitches available for the…

view full answer...

Answer 10

It sounds like you may already have a 4 way connector on your vehicle, which is half of the battle. In order to operate the Curt Echo Mobile Wireless Brake Controller #C51180 you will need an almost fully functional 7 way connector; using something…

view full answer...

Answer 11

Hey Andrew. The Redarc Tow-Pro link will indeed work just fine for your 2026 Toyota BZ, and due to it not needing a brake output wire you do not need to hook up the brake out put wire at all. You'll plug the USCAR pig tail #20147 into the Tow-Pro…

view full answer...

Answer 12

Hey John, good question. The app must be running in order for the separate manual override button part #C83HR to work. If your phone is not connected to the controller with the app running, the button will not do anything. I know the connectivity…

view full answer...

Wheel Lock Nuts for 2020 Cargo Mate Trailer BL58SA

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching