How to Mount the UWS A-Frame Trailer Toolbox on a Trailer?
Published 01/09/2020 >
Question:
It looks like some kind of installation hardware is not included with the box and is not in the related hardware. What installation hardware is recommended for a good solid install?
asked by: Mike
Helpful Expert Reply:
These toolboxes do not contain mounting hardware due to the different construction and mounting locations that may be required for many different styles of trailers. A lot of how you install the UWS A-Frame Trailer Toolbox # UWS01065 depends on where on the trailer tongue you'll be mounting this, but you'll at least need a few inches in front of the wall of the cargo enclosure to allow for the opening of the box.
I would recommend using a properly sized drill bit to drill 4 mounting holes in the proper locations on your trailer frame. Keep the holes as far to the front, back and sides of the box as possible for the most secure connection. Then use bolts, washers and nylon lock nuts to secure the box to the frame. You could also use, properly sized, self tapping screws with washers and secure the box to the trailer frame in this fashion. Bolts, 3/8 inch size, should be sufficient to secure the box.
You could also weld some L shaped rails the width of the trailer frame, spaced 18" apart, and mount the toolbox to these brackets instead of the trailer frame. I've linked a photo of how one of our customers did this that might be a good guide to use if you wanted to go that route.
Product Page this Question was Asked From
UWS A-Frame Trailer Toolbox - 6.3 cu ft - Gloss Black
- Trailer Tool Box
- A-Frame Tool Box
- 19 - 22 Inch Tall
- Aluminum
- 41 Inch and Longer
- Black
- UWS
more information >
Continue Researching
- Video: Review of Victron RV Power Inverter - Inverter MultiPlus II Inverter Charger AC Outputs - VN73VR
- Shop: Victron MultiPlus Pure Sine Wave Inverter Charger - 1,600 Watts - 50 Amps - 24V - UL Listed
- Shop: Victron MultiPlus Pure Sine Wave Inverter Charger - 2,000 Watts - 50 Amps - 12V - UL Listed
- Shop: Victron MultiPlus-II Inverter Charger with 1 AC Input - 2,400 Watts - 50 Amps - 24V - UL Listed
- Shop: Victron MultiPlus-II Inverter Charger with 1 AC Input - 2,400 Watts - 50 Amps - 12V - UL Listed
- Search Results: l44649 / l44649 trailer hubs and drums
- Search Results: bearing l44649 and l68149 trailer bearings races seals caps
- Video: Timken Bearing Kit Step-By-Step Replacement - Utility Trailer
- Video: A Closer Look at the Timken Bearing Kit for Lippert, Dexter, and AL-KO Axles
- Shop: etrailer Trailer Tool Box - A-Frame - Aluminum - 3.4 Cu Ft - 34" Long - Matte Black
- Shop: RC Manufacturing T-Series Trailer Tongue Tool Box - A-Frame - Steel - 2.6 Cu Ft - Black
- Search Results: axletek
- Search Results: uws trailer tool box
- Shop: UWS A-Frame Trailer Toolbox - 4.1 cu ft - Bright Aluminum
- Video: UWS A-Frame Trailer Toolbox Spec Review
- Video: The Low-Down on the UWS A-Frame Trailer Toolbox
- Video: Review of etrailer Trailer Tool Box - Matte Black Aluminum A Frame Trailer Tool Box - e64VV
- Video: UWS A-Frame Trailer Toolbox Feature Review
- Search Results: storage box trailer cargo organizers
- Search Results: trailer tool box
- Search Results: trailer storage
- Shop: Towing Mirrors
- Q&A: Do You Carry a Axle Rated for 3,500 with Hub Face to Hub Face of 94", of do I Need the 95"?
- Q&A: Comparing etrailer And Dexter 3,500lb 4 Drop Axles
- Q&A: Replacement Spindle and Axle Options For a 3,500LB Trailer Axle With Bent 4 Drop Spindle
- Q&A: Install Video for Trailer Axle w/ Electric Brakes - 4 Drop - 5 on 4-1/2 Bolt Pattern - 95 Long
- Q&A: Trailer Jack Option That Allows Me To Lower My Tailgate When Towing My Casita Travel Trailer
- Q&A: Lowest-Profile A-Frame Trailer Jack For Tailgate Clearance
- Q&A: Will Self-Tapping Screws Hold Trailer Tongue Tool Box 350970 on Aluminum Trailer


