Can While Lithium Grease be Used As Assembly Lube for Fulton F2 Winch

Question

Question:

I just replaced all Gears and assembly parts on my Fulton F2 3200 lb Winch, and was wondering if I was OK in using White Lithium tub grease for the lubrication?

asked by: W. D

0

Expert Reply:

Yes, using white lithium grease like LubriMatic in a 14 oz cartridge # L11354 as lubrication for your Fulton XLT winch # F142425 would be totally fine.

expert reply by: Jameson C

0

Answer 1

For your 1984 Tee Nee trailer, the number of leaf springs is not the determining factor but rather the length and the capacity rating. The 3-Leaf Slipper Spring w/ Flat End for 2,900-lb Trailer Axles - 30" Long #SP-039275 is a great replacement…

view full answer...

Answer 2

Hello Kenneth. I reached out to Fulton and they informed me that the ratchet plunger knob has been discontinued with no replacement. My apologies that this replacement part is not longer available. The only replacement parts for the Fulton F2 Fully…

view full answer...

Answer 3

I spoke to my contact at Fulton and he said the correct replacement spring for the ratchet of your Fulton F2 winch is the part #4769-28. I attached a picture that shows a diagram for the winch for you to check out. You will be able to see how the…

view full answer...

Answer 4

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 5

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 6

You can use leaf springs that are rated higher than the axle without any issues as long as they measure the correct measurement for your trailer. For example the 6-leaf double eye spring for 7,000 lb axles part #e64SR measures 24-7/8" eye to…

view full answer...

Answer 7

Trailer wheel bearings are specific to the spindle that is installed on the axle that is on your trailer. You will need to safely support the trailer, remove the wheel and tire, remove the grease cap, remove the cotter pin and washer that secures the…

view full answer...

Answer 8

Hey Ian, great to hear from you again! The differences between the MORryde CRE3000 #MR87ZR and AllTrek 4000 #MR89DR that fit a 33" wheelbase is the height between the hanger and equalizer bolts, and the amount of travel the suspension style will…

view full answer...

Answer 9

We have lift kits for trailer that easily add 2 inches to the height of the trailer. For that you'd want the part #RR23QX and you'd be set. I attached a picture that shows how it installs to give you an idea. This would be the easiest…

view full answer...

Answer 10

There is no exact way to determine the leaf spring length. The best way to determine the length for a replacement is by measuring the existing leaf springs. The hanger distance and shackle length can help you get a good idea, but you're looking…

view full answer...

Answer 11

Hi Austin, I can help you determine the right replacement double-eye leaf springs for your 2018 Jayco trailer, though we don't have any way of knowing what specific ones you need. It's pretty easy though, as all you need to do is measure your…

view full answer...

Answer 12

Hey Jason, it's pretty common for replacement leaf springs to be slightly shorter than what they replace as springs tend to stretch/flatten overtime as they wear out so while you are on the right track 3/4 of an inch is a bit too much of a…

view full answer...

Can While Lithium Grease be Used As Assembly Lube for Fulton F2 Winch

Products Featured in This Question

Continue Researching