Replacement Metal Uprights for CE Smith Guide Ons # CE27670

Question

Question:

I recently purchased 2 sets of part 27620 from you and I have bent two of the the post—are they ava

asked by: Ron W

0

Expert Reply:

For replacement metal posts for the CE Smith Guide Ons part # CE27670 that you have you'd need the part # CE27608PG and you'd be set.

expert reply by: Jameson C

0

Answer 1

The guide posts will fit, as long as your frame members aren't wider than 3-3/4 inches wide and 4-1/4 inches tall. They are adjustable up to 13-inches from the outside edge of the trailer frame. (See picture to the right). The guide posts extend…

view full answer...

Answer 2

I took the picture you sent in and put the dimensions you are looking for on them. I attached the dimensions to this page for you to check out as well.

view full answer...

Answer 3

The best size guide on to get would be the one that works based on where you would attach them to your frame and the height of the boat. Ultimately that is up to you to decide. We have the #CE27620 which are 40" tall and also the 60" tall…

view full answer...

Answer 4

Post-Style Guide-Ons for Boat Trailers, like #CE27646 are designed to help you load your boat onto your trailer. Because the rear of the trailer is backed into the water, it makes it really hard to see if you're loading it straight onto the…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 7

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 8

The Demco Hydraulic Trailer Brake Actuator part #DM72VR should be a direct replacement for the Atwood 61101 Brake Actuator that you have now. This newest updated it rated at 7K instead of 6K. This is a bolt on option that mounts on 3" centers.…

view full answer...

Answer 9

You can use leaf springs that are rated higher than the axle without any issues as long as they measure the correct measurement for your trailer. For example the 6-leaf double eye spring for 7,000 lb axles part #e64SR measures 24-7/8" eye to…

view full answer...

Answer 10

Trailer wheel bearings are specific to the spindle that is installed on the axle that is on your trailer. You will need to safely support the trailer, remove the wheel and tire, remove the grease cap, remove the cotter pin and washer that secures the…

view full answer...

Answer 11

Hey Robert, yes the Kodiak disc brake calipers part #KDBC225DAC that you referenced will replace the Tie Down calipers you have now 46304, they can be used as a left or right hand caliper and does come with ceramic brake pads. If you ever needed…

view full answer...

Answer 12

Hey Steven! The etrailer Rust-Resistant 3-Leaf Double Eye Spring for 4K Trailer Axles - 25-1/4" Long - Dacromet #e93SR will be adequate for your 2020 Gulf Stream Vista Cruiser since the Dexter D40 number correlates to a 4,000 lbs hub and drum…

view full answer...

Replacement Metal Uprights for CE Smith Guide Ons # CE27670

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching