Replacement Cap for Ram 1000 Series Marine Jack

Question

Question:

I have a RAM marine jack on my trailer and the cap is missing and the jack said its the 1000 series, so will this cap fit the top of my jack?

asked by: Leonard

0

Expert Reply:

We do have the cap you need, which is the Replacement Cap for etrailer and Ram Swivel Marine Jacks - 1,000 lbs # MJ-1000B-CP, which is designed for the MJ-1000B Series jacks

The cap you referenced, the Replacement Cap for etrailer and Ram Swivel Marine Jacks - 1,500 lbs # MJ-1500B-CP is designed to work with a different model, the MJ-1500B Series jacks.

expert reply by: Kyle S

0

Answer 1

We do have a few great options for protecting your vehicle from road debris when being towed behind your motorhome. If you have a Roadmaster tow bar with quick disconnects, I recommend looking at the Roadmaster Guardian Rock Guard #RM-4000. This is a…

view full answer...

Answer 2

We do have replacement caps available for swivel jacks. If this is an actual etrailer jack you need one of the following: -Replacement Cap #MJ-1000B-CP (for MJ-1000B Series) -Replacement Cap #MJ-1500B-CP (for MJ-1500B Series) I noticed you looked at…

view full answer...

Answer 3

Thanks for reaching out, Davide! I believe the Replacement Cap for etrailer and Ram Swivel Marine Jacks - 1,500 lbs #MJ-1500B-CP will work for your application as it has a 2.08" ID and a 2.19" OD (see attached).

view full answer...

Answer 4

Although I'm not sure what jack you have, we do have a handful of replacement caps for Ram jacks. Ram Square, Direct Weld, Sidewind Jack 10K - #TJD-12000-CP Ram Sidewind 2,000 lbs A-Frame Jacks - #TJA-2000S-CP Ram Swivel Marine MJ-1500B Series…

view full answer...

Answer 5

Sure we have plenty of replacement caps for RAM jacks, however I would need a bit more information to get you the right cap. For instance, if you had a TJA-2000S series jack then you could use the Replacement Cap for etrailer and Ram Sidewind A-Frame…

view full answer...

Answer 6

We have another Dutton Lainson jack cap that's slightly smaller than what you bought. The part #DL22354 has an outer diameter of 1.98 inches and is most likely what you need based on your picture. Since you are wanting to be extra cautious this…

view full answer...

Answer 7

I went out to the warehouse and measured Replacement Cap #MJ-1500B-CP for you. The threaded part has a diameter of 2.08 inches. The overall diameter is 2.19 inches. I have included a picture showing these measurements.

view full answer...

Answer 8

The 2 inch cap you are looking for for the top of your Lippert powered trailer jack is the part #LC115863. The price and "add to cart" button are down below on this page.

view full answer...

Answer 9

Although we do not carry the Reese TowPower Side Wind Trailer Jack, I may have a solution for you. The Replacement Round Cap for Pro Series and Fulton Trailer Jacks #PS500322 is a round plastic dome cap that is compatible with jacks that have a…

view full answer...

Answer 10

I believe the gears you need are #BD500106. There is a picture on the product page below the description that shows the measurement of each piece so you can compare them with what you have. For caps there are a few different options. Cap #F091754000…

view full answer...

Answer 11

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 12

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Replacement Cap for Ram 1000 Series Marine Jack

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching