Available Sizes of Winch Roller Fairleads

Question

Question:

I purchased the BDW30003 for a older warn winch that I want to use, The spool width is 7 inches wide and the replacement fairlead that i bought the inside width is 10 inches and my cable want to ride on the edge of the spool which thats not good ! Do you have a 8 inch one that would work ?

asked by: Steve V

0

Expert Reply:

We do have a winch roller fairlead that is 8-inches, Bulldog part # BDW20022, and we have others that are shown on the linked page. Another one similar in size is ComeUp Roller Fairlead # CU880023 which has a throat size of 8.27-inches. For a fairlead that is 8-inches overall with hole spacing of 6-1/2-inches we have Bulldog part # BDW20059; this item is shown in the linked photo.

expert reply by: Adam R

0

click to enlarge

Answer 1

I reached out to the manufacturer and confirmed that the Bulldog Winch Roller Fairlead for Powersports - 165 mm Mount #BDW20059 uses nylon/plastic bushings. My tech contact said he doesn't know of any fairleads that have bearings whether plastic…

view full answer...

Answer 2

For you, you'll just need to order two of the Dexter Nev-R-Adjust Electric Trailer Brake Assembly #23-464 for the left hand, and #23-465 for the right hand side.

view full answer...

Answer 3

You have to be careful if you lubricate electric trailer brakes such as #23-468. You cannot get any grease on the pads or on the inside of the drum because that will have a negative impact on brake performance. The magnet arm and the shoes pivot at a…

view full answer...

Answer 4

I called my contact at Dexter to ask about the Nev-R-Adjust Electric Brake Assembly like part #23-459. They told me that most brake assemblies wear at different rates. With the Nev-R-Adjust brakes he said they will wear very well and that if they…

view full answer...

Answer 5

Well. the reason you can't replace your old Hayes brake assemblies with the Dexter #23-105 or the etrailer #AKEBRK-6R is due to differences in the designs of the assemblies backing plates. I recommend sticking with the Hayes/AL-KO brake…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 8

Trailer wheel bearings are specific to the spindle that is installed on the axle that is on your trailer. You will need to safely support the trailer, remove the wheel and tire, remove the grease cap, remove the cotter pin and washer that secures the…

view full answer...

Answer 9

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 10

I currently have three diffrent self-adjusting assemblies for your boat trailer with 10" x 2-1/4" electric drum brakes which are attached for you below. eTrailer Electric Trailer Brake Kit part #AKEBRK-35-SA (3,500 Axles) Dexter…

view full answer...

Answer 11

The Tru Ryde grease seals you mentioned, part #RG06-70 are indeed a replacement for the 10-036-00 Dexter seals. They would work great for your application.

view full answer...

Answer 12

After you've packed the bearings and assembled everything, carefully slide the hub assembly onto the spindle and install the outer bearing. Install the spindle and tang washer and run the spindle nut down finger tight, then rotate the hub back…

view full answer...

Available Sizes of Winch Roller Fairleads

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching