Replacement T-Bolt for Front Jaw on Yakima ForkLift Bike Rack # Y02098

Question

Question:

I can not find for this part the Bolt that is used to pull the clamp together. I see one for the rear clamp, but the front camp was a different size. I lost the camp and bolt together.

asked by: Wesley

0

Expert Reply:

For the bolt that is used to close the Replacement Front Jaw # Y8880189 for the Yakima ForkLift Bike Rack # Y02098 you need the Front and Rear Adjusting Handles # 8880139 and Replacement T-Bolts # 8860061. The bolts themselves are the same size; it's the handles that are different sizes. I have confirmed with Yakima that these are the parts that you need.

expert reply by: Jon G

0

Answer 1

You have the Yakima Control Towers with round crossbars. In one of the pictures you can make out the Yakima logo on the base of the tower. The tightening tool for this is a 5 millimeter hex wrench, part #8880143.

view full answer...

Answer 2

Thanks so much for that detailed info, and we do have the exact adapter you need so you can mount your Thule Echelon 518 bike rack to your Rapid Aero crossbars, and it is indeed an Xadapt: - Thule Load Bar Adapter for Peloton and Echelon Bike Racks…

view full answer...

Answer 3

Hey Lisa, yes you can use a hitch reducer with the EcoHitch part #EH87CR to reduce it down to a 1-1/4 inch hitch size like with the part #HT02. Do you have a bike rack for that hitch size currently?

view full answer...

Answer 4

The catch to using accessories with round bars like the SeaSucker Monkey Bars #298-SX6000B you referenced is that you need to have the unit the accessory is meant to hold installed so that they don't fall over. What you are experiencing with the…

view full answer...

Answer 5

With the Yakima LoadWarriors like the part #Y07070 what you'd do is use either the front bar of the basket as the front crossbar, or you can use the part #8870042 so that you can use the fairing, and then use the rear rail edge of the basket for…

view full answer...

Answer 6

From your statement and the pictures, it looks like you are needing the mounts that allow you to attach the Yakima FrontLoader to the crossbars. If that is the case, we do have the rear mount/clamp. - Replacement Rear Clamp Assembly for Yakima…

view full answer...

Answer 7

If you're wanting to replace the read bar clamp on your Yakima FrontLoader #Y02103, then this is the complete Rear Clamp Assembly #8880208 but if you think the hardware and clamp #Y8880192 is all you need to replace, we have that as well.

view full answer...

Answer 8

Hi Mary, There can be differences in the way components under the vehicle are ran that can change how a trailer hitch will need to be shaped to fit depending on the model type. I spoke with EcoHitch and they stated that they haven't tested the…

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

Hey Casey, the highest tongue weight rated hitch we carry for your 2021 Toyota Camry is the Draw Tite part #36643 which has a tongue weight rating of 350 lbs. Then for trailer wiring the best option is the Tekonsha part #118763 which installs easily…

view full answer...

Replacement T-Bolt for Front Jaw on Yakima ForkLift Bike Rack # Y02098

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching