How Much Can a 2014 Toyota Tacoma Tow with the Bumper
Updated 04/24/2019 | Published 04/22/2019
Products Featured in This Question
Question:
Can I tow a Jon boat with trailer from my 2014 Toyota Tacoma bumper hitch
asked by: Matt
Expert Reply:
The towing capacity of the bumper on your 2014 Toyota Tacoma assuming you have the cutout will vary from 3,300 - 3,500 lbs depending on options. I advise you to take a look starting at page 228 of your owner's manual to see these options. Therefore, so long as your jon boat does not exceed the above then you will be good to go. If you need a hitch ball, I recommend the Hitch Ball part # C40017 for 1-7/8" or part # C40020 for 2" so long as you have a 1" diameter ball hole.
If your jon boat does exceed the above then you will want to install a trailer hitch. Also, it can be hard to tow level using a bumper so if you need to travel long distances to get your boat in the water then I would recommend installing a trailer hitch anyway. For this, the Draw-Tite Max-Frame Trailer Hitch Receiver part # 75236 is what I would use as it's a custom fit so no drilling is required and it will allow you to tow a much heavier trailer while level, up to 5,500 lbs if the vehicle is equipped to do so.
If you don't already have a trailer wiring harness then you will need one of these as well for which I recommend the T-One Vehicle Wiring Harness part # 118496 because again it is a custom fit which this time means no splicing. For a ball mount/hitch ball, the Curt Channel Style Adjustable Ball Mount part # C45900 will have you covered.
I have attached install videos and a photo for you as well.
Product Page this Question was Asked From
1-7/8" Hitch Ball - 1" Diameter x 3" Long Shank - Chrome - 3,500 lbs
- Trailer Hitch Ball
- Trailer Hitch Ball
- Standard Ball
- Chrome-Plated Steel
- 3500 lbs GTW
- 1-7/8 Inch Diameter Ball
- 3 Inch Shank Length
- 1 Inch Diameter Shank
- CURT
more information >
Featured Help Information
Miscellaneous Media
Continue Researching
- Shop: Trailer Wiring
- Shop: T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Q&A: Wrench and Socket Sizes Needed To Tighten Curt 1-7/8" Hitch Ball # C40002
- Q&A: What Size Hitch Pin Hole does the B&W Pintle Hook Mounting Plate for 2" Hitches Have?
- Article: Wiring Trailer Lights with a 4-Way Plug (It's Easier Than You Think)
- Q&A: Will etrailer Hitch e63ZR Fit 2023 Ford Ranger Tremor With OEM Rear Tow Hooks?
- Q&A: Do Chain Hooks on 2022 Ford Ranger Have to be Removed to Install Curt Trailer Hitch Receiver
- Q&A: Do Any Modifications Need to be Made to a 2007 Volvo S-80 to Install Curt Trailer Hitch # 12287
- Article: Types of Trailer Hitches: How and Why to Use Each
- Article: Wiring Trailer Lights with a 7-Way Plug (It's Easier Than You Think)
- Q&A: Dexter Replacement Brake Assemblies that are 12-1/4 inch by 2-1/2 inch
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Article: Holiday 2025 | Best Gifts for Towers
- Article: Trailer Maintenance Schedule
- Article: Routing the Power Wire for a Trailer Wiring Harness