Replacement Parts for Dutton Lainson Roller Bunk DL21740

Question

Question:

Can I get replacement rollers, roller shafts and cap nuts for the DL 21740?

asked by: Mike H

0

Expert Reply:

For the Dutton Lainson Roller Bunk # DL21740 we have replacement roller # DL203228 which will fit roller shaft # CE10700A that includes the two cap nuts. The shaft is 5-1/4-inches long.

expert reply by: Adam R

0

Answer 1

For the Dutton Lainson Roller bunks part #DL21754 we have replacement rollers. For that you would want the part #DL203228. I attached a review video for this roller for you to check out as well.

view full answer...

Answer 2

There have not been any updates to the CE Smith Rollers, but you may want to consider the Replacement Roller for Dutton Lainson Roller Bunks #DL203228 which are a little stronger as the roller is made for boats up to 1,000 lbs heavier than the CE…

view full answer...

Answer 3

We have 2 different sets of roller bunks with a 3,000lb capacity from Dutton-Lainson. First is the Deluxe Roller Bunk #DL21741 which is made of 12-gauge, galvanized steel and is 5' long per side. The 12 sets of 3 Rollers #DL203228 are removable…

view full answer...

Answer 4

You can install the 4' Long Boat Trailer Standard Roller Bunks #DL21754 directly on top of your carpeted wooden bunks (without removing the carpet first). These have a weight capacity of 2,500 lbs per set so 4 roller bunks would be very…

view full answer...

Answer 5

The size of bunk board or bunk roller you will need for your boat trailer is based off the hull size. However, generally speaking the manufacturer knows what size roller/bunk works best for the boat/trailer. Therefore I recommend using the same size…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

Yes, you would want to use two sets of 4 foot roller bunks since your current bunks are 8 feet long. I would recommend you go with the Dutton-Lainson Boat Roller Bunks #DL21740. These roller bunks would have plenty of capacity and would be sized…

view full answer...

Answer 8

We do have a variety of roller bunks that can be used as a direct replacement for carpeted bunks. I recommend either going with the 2,500 lb capacity which comes in Black #DL21754 or Silver #DL21740, OR the 3,000 lb capacity which also comes in Black…

view full answer...

Answer 9

The longest section of roller bunks we offer is 5 feet like the part #DL21741 that you referenced. For a 10 foot long section you would want to use one 5 foot section like the #DL21741 and then a set of 4 feet long roller bunks like the part…

view full answer...

Answer 10

If you have adjustable brackets for the bunk boards then you could lower them down and mount the CE Smith Roller Bunks for Boat Trailers #CE27710 directly to them. If you don't have adjustable brackets then you would need to remove the bunk…

view full answer...

Answer 11

You could use roller bunks such as #DL21740 on a pontoon boat trailer. If the pontoons sit on carpeted bunks and support the boat then you would need to place rollers the whole length of each of the carpeted bunks. Set #DL21741 is rated higher at…

view full answer...

Answer 12

A couple sets of the Dutton-Lainson Boat Trailer Deluxe Roller Bunk - 5' Long Sections - 12 Sets of 3 Rollers #DL21741 will drastically help with getting your pontoon boat on and off the trailer smoothly and easily as there isn't any friction…

view full answer...

Replacement Parts for Dutton Lainson Roller Bunk DL21740

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching