Which Opti-Brite LED Dome Light Comes with Ring to Cover Screw Holes

Question

Question:

Does this have a plate to cover screw holes.

asked by: Chris S

0

Expert Reply:

The Opti-Brite LED Dome Light # ILL10CCB that you referenced does not have a plate or ring to cover the screw holes. The closest version of this light that does have this is the Opti-Brite LED Dome Light # ILL06COB which is smaller at 11 inches by 4 inches.

expert reply by: Jameson C

0

click to enlarge

Answer 1

We have many different LED lights for the interior of an enclosed trailer, though I'm not 100 percent sure what you are referring to by shop-type lights. But we have lights such as the Opti-Brite LED RV Dome Light #ILL10CCB and Gustafson 12V RV…

view full answer...

Answer 2

The Opti-Brite LED RV Dome Light #ILL10CCB that you referenced is sold individually. Sometimes the Optronics part numbers end up listed as their bulk part number. I can assure you though that this #ILL10CCB is sold individually. I attached a review…

view full answer...

Answer 3

The Opti-Brite LED Interior Light part #ILL08COB and part #ILL10CCB are idenical lights for the exception of the number of diodes they contain. The light ending in "COB" contains 8 diodes whereas the light ending in "CCB" has 10…

view full answer...

Answer 4

As far as physically mounting the Opti-Brite work light #TLL60FB it has a bracket that you can just bolt directly to the mounting surface so that much is easy. Just be sure to use hardware that is appropriate for the mounting surface material. Wiring…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 10

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 11

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 12

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Which Opti-Brite LED Dome Light Comes with Ring to Cover Screw Holes

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching