How Does Wheel Rim Clamp for Mobile Home Style Hubs, # 15-2 Install

Question

Question:

On a mobil home wedge does where it say wheel on it goes towards the hub and the rim side goes to the rim

asked by: Jamey S

0

Expert Reply:

On the Wheel Rim Clamp for Mobile Home Style Hubs, # 15-2, the portion with the lip goes toward the inside of the hub and opposite the nut. The angled side goes to the outside of the wheel so as you tighten the nut it pushes against the lip on the inside putting pressure to the angled section on the outside to hold your wheel tight.

expert reply by: Jameson C

0

Answer 1

The Dexter Trailer Hub and Drum Assembly, part #8-174-5UC3, includes the lug nuts and rim clamps that hold the wheel on to the hub. The lug nuts are part #916N and have a 9/16-inch fine thread. The replacement stud that is installed in the hub…

view full answer...

Answer 2

The Never Fail upgrade kits like the #LC281285 have two really distinct advantages. One of them is what you mentioned and is that they don't require greasing or any maintenance. The other is that they last about twice as long as any other heavy…

view full answer...

Answer 3

The Suspension Kit for Tandem-Axle Trailers - 1-3/4" Wide Double Eye Springs #AP233 is the standard suspension kit. For a heavy duty option, we have the Dexter Axle Heavy-Duty Suspension Kit for Tandem Axle Trailers - 1-3/4" Double Eye…

view full answer...

Answer 4

On the Wheel Rim Clamp for Mobile Home Style Hubs, #15-2, the portion with the lip goes toward the inside of the hub and opposite the nut. The angled side goes to the outside of the wheel so as you tighten the nut it pushes against the lip on the…

view full answer...

Answer 5

It sounds like you're looking for the fuse that controls the 12v power to your 7 way connector. The fuse for the 12v power on a 2007 Chevy Silverado (New Body Style) is located at the front of the power distribution box under the hood of the…

view full answer...

Answer 6

The correct way to wire your breakaway battery, like the Hopkins Engager #20400, is to have the black wire from the battery connected to the 12V power on your trailer, and then the blue wire to your breakaway switch which, in turn, connects to the…

view full answer...

Answer 7

The diagram you attached shows a 7-way wired up in what is considered the "traditional way." If you check out the chart I attached you will see the three ways (really only 2), that a 7-way can be wired. The Featherlite is wired up like the…

view full answer...

Answer 8

I spoke with my contact at Redline and he said the Wheel Rim Clamp for Mobile Home Style Hubs #15-2 goes towards the hub. So the flat side of it goes up against the lug nut.

view full answer...

Answer 9

The Redline Grease Seal part #10-40 is what you need to replace a Dexter Grease Seal 010-004-00, they are the same dimensions. The only difference is that this new seal is a double lip and the one you have is a single, double has better protection…

view full answer...

Answer 10

The Dexter 8-222 model hubs currently on your trailer are designed primarily for mobile home use, and these types of hubs typically use unique bearing combinations that make it really difficult to find full replacement assemblies. Mobile home parts…

view full answer...

Answer 11

Hey David, thanks for the picture. I was able to track down a spec sheet for your Dexter axle which I have included below. The 031-029-02 bearing is item #15123 and the 031-030-02 bearing is item #25580. For a bearing kit you can use part #BK3-110…

view full answer...

Answer 12

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

How Does Wheel Rim Clamp for Mobile Home Style Hubs, # 15-2 Install

Product Page this Question was Asked From

Continue Researching