Replacement Global Link Strike Plate and Edge Plate for Entry Door

Question

Question:

Do the Global link strike plate 295-000022 and edge plate 000023 when ordered do the parts come with the screws also?

asked by: Melvin L

0

Expert Reply:

The Global Link Replacement Strike Plate for RV Entry Doors - Steel # 295-000022 and Global Link Replacement Edge Plate for RV Entry Doors - Steel # 295-000023 do not come with mounting hardware. I've linked a photo and a video to help with dimensions, but the hardware only comes with the complete kits like # 295-000019 for example.

expert reply by: Jason S

0

click to enlarge

Answer 1

I do have a couple of options for you that are pretty universal and work with most trailers. However, since there isn't a way to cross reference your specific trailer year, make and model, you'll need to take a couple quick measurements to…

view full answer...

Answer 2

We do have replacement RV Entry Door Handles like the Global Link #295-000019 as well as deadbolts like the Valterra #L32CS3108 with 1" throw, but these are keyed separately as we don't have an all-in-one kit with both locks keyed. Alike.…

view full answer...

Answer 3

Yes, the 921 #VA0415-00 and the 922 bulbs are the same size and will fit into the same socket; the only difference is the brightness.

view full answer...

Answer 4

While we do not have the ability to pull part numbers from OEM build sheets, from images online it appears similar to #PLR5115. The measurement on this option is 5-1/2" by 4-1/4" requires a cutout of approximately 4-5/8" by…

view full answer...

Answer 5

I wish we had something that was close to what you need but I checked and we only really have options that are slightly longer and a little narrower.

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 9

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 12

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Replacement Global Link Strike Plate and Edge Plate for Entry Door

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching