Replacement Slide Out Motor Recommendation for 9,000 RPM Slide Out Motor

Question

Question:

would this set up work to replace the 9000rpm gearing that has chewed up plastic gear

asked by: Mike B

0

Expert Reply:

Since you said what you have is the 9,000 RPM model the correct replacement motor is the part # LC125802. This is a Tuson High Speed 18:1 9,000 RPM slide out motor.

expert reply by: Jameson C

0

Gary L.

7/1/2020

Can you purchase the plastic gear in the gearbox item#LC 125802 18:1 for Lippert through- frame slide-outs

Chris R.

7/6/2020

Unfortunately the gear box isn't available separately from the Lippert Motor part # LC125802.

Answer 1

It's totally fine to replace the oil in an oil bath hub with grease without changing anything else. The bearings will be properly lubricated and the seals will work just fine. I actually prefer grease to oil bath hubs mainly because if for some…

view full answer...

Answer 2

Thanks for the picture of your slide out motor. Based on that I can tell that the correct replacement motor is the part #LC132682.

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 5

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 6

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 7

You can use leaf springs that are rated higher than the axle without any issues as long as they measure the correct measurement for your trailer. For example the 6-leaf double eye spring for 7,000 lb axles part #e64SR measures 24-7/8" eye to…

view full answer...

Answer 8

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 9

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 10

Hey Victor, yes the Long U-Bolt Kit part #RM33KT is a Roadmaster brand u-bolt kit. This does include nuts and washers as well.

view full answer...

Answer 11

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 12

The two sizes you mentioned are pretty similar and fit many of the same 15 inch wheels. The 205/75-15 fits rim widths of 5 inch to 6 inch whereas the 225/75-15 fits widths that are 5 inch to 6-1/2 inch. The 205 is 27.1 inches tall and the 225 is 28.4…

view full answer...

Replacement Slide Out Motor Recommendation for 9,000 RPM Slide Out Motor

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching