Hub Bore Diameter of etrailer.com Trailer Idler Hub Assembly # AKIHUB-545-2-G-2K
Published 09/14/2018 >
Products Featured in This Question
Question:
What is the diameter of the part of the hub Item # AKIHUB-545-2-G-2K that fits into the center hole of a wheel? I want to be sure my wheel will fit. Thanks. Since you dont provide this dimension, Im guessing its so standardized that most wheels will fit most hubs, but Id like to be sure.
asked by: Ron
Expert Reply:
I went out to our warehouse and measured an outer bore diameter of 2-1/4 inches on the etrailer.com Trailer Idler Hub Assembly # AKIHUB-545-2-G-2K that you referenced. The reason we don't typically list this dimension on our trailer hubs is because a vast majority of trailer wheels are lug centric and not hub centric, which just means that the wheels are secured by the lugs instead of centered on the hub. Because of this the only thing you need to make sure of is that your wheels have a pilot hole that is larger than the hub bore on your trailer hubs so that it fits over them. They do not need to be the same size.
This particular hub assembly is designed for 2,000 pound axles, uses the # L44649 inner and outer bearing, and has a 5 on 4-1/2 inch bolt pattern. I have attached an installation video that you might also find helpful.
Product Page this Question was Asked From
Trailer Idler Hub Assembly for 2,000-lb Axles - 5 on 4-1/2 - Galvanized
- Trailer Hubs and Drums
- Idler Hub
- Standard
- L44649 / L44649
- Marine Grade
- For 2000 lbs Axles
- 1/2 Inch Stud
- 5 on 4-1/2 Inch
- 10 Inch Wheel
- 12 Inch Wheel
- etrailer
more information >
Featured Help Information
Miscellaneous Media
Continue Researching
- Shop: Trailer Hitch
- Search Results: 95188
- Shop: Flange Wheel Nut - 5/8"
- Shop: Replacement Trailer Hub Wheel Stud, Drive-In, 5/8" x 3-1/8" (Qty 4)
- Q&A: What are the Dimensions of a #99 Spindle
- Search Results: spindle washer
- Search Results: 370150a
- Search Results: bp01~301
- Search Results: dexter magnet
- Search Results: timken bearing kit
- Search Results: alko
- Q&A: What Would Need to Change to Go from Single Wheel Axle on Trailer to Dually
- Q&A: Wheel Stud Size and Replacements for Dexter Trailer Hub Assembly 8-214-5
- Q&A: Length of Spline Section of Replacement Trailer Hub Wheel Stud
- Q&A: Torque Specification for Lugs Nuts on 5/8-Inch Stud on Dexter Hub
- Q&A: Can Dual Wheels On 10K Dexter Axles Be Changed Over To Super Single 17.5" Wheels and Tires?
- Shop: Americana Modular Wheel w/ -0.5 Offset - 17-1/2" x 6-3/4" Rim - 8 on 6-1/2 - Silver
- Shop: etrailer Electric Trailer Brakes w/ Dust Shields - Self-Adjusting - 12-1/4" - Left/Right - 10K
- Shop: Dexter Fortress Threaded Aluminum Oil Bath or Grease Cap for Dexter 9K to 10K General Duty Axles
- Shop: Dexter Brake Drum Mounting Screws - 1-1/2" Long x 1/2"-13 - Qty 1
- Shop: Timken 412920 Grease and Oil Seal - I.D. 2.250" / O.D. 3.376" for 5.2K, 6K, and 7K Axles
- Q&A: What is the Difference Between 7-Way RV and Utility Trailer Connectors
- Shop: Gooseneck Hitch



