What are the Dimensions of Fulton Plastic Trailer Fender # F008584 and # F008585

Question

Question:

could you please give me a diagram for the 2 fenders listed above?i am tring to replace the fenders on my tidewater tr6300dr15inch tires

asked by: Jerry L

0

Expert Reply:

I would be happy to provide the dimensions for the Fulton Plastic Fender, # F008584 and # F008585. I have actually made a picture showing the dimensions for you.

expert reply by: Michael H

0

click to enlarge

Answer 1

I went out to our warehouse to take a couple measurements on the CE Smith Single Axle Trailer Fender #CE19504 that you referenced. The inside arch between the two side steps measures 30-5/8 inches long. The step itself which I believe is what you…

view full answer...

Answer 2

You're on the right track, but the easiest and probably most secure way to run your ground circuit is to simply use the trailer frame for the ground. Ground your white wire to the trailer tongue as it comes off the trailer connector. Just use a…

view full answer...

Answer 3

We have a great option for plastic fenders for your trailer with 15 inch wheels and 205/75-15 tires, the Fulton Single Axle Trailer Fenders with Top and Side Steps #F008585-2 (Black) or #F008595-2 (Silver). These fenders are designed for use with…

view full answer...

Answer 4

The Fulton Single Axle Trailer Fender #F008594-2 does have a 4-1/8" wide mounting bracket slot, so they will fit nicely with the 4" wide brackets on your McClaine trailer. The mounting holes on the fender are 3-3/4" apart though, so…

view full answer...

Answer 5

Hey Ryan, the bracket kit part #PF1135-BKT-2 is normally the best solution as long as the trailer has a frame rail that runs the perimeter of it. Then if the frame is 2 inches wide you would want the part #CE15284GA and you'd be set. The other…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 11

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 12

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

What are the Dimensions of Fulton Plastic Trailer Fender # F008584 and # F008585

Continue Researching