Will Inno Square Crossbars Fit Thule Roof Racks Square Feet

Question

Question:

I need a longer crossbar than my current Thule 50inch bars 2 canoes. Will these bars fit a thule square bare system?

asked by: Don

0

Expert Reply:

I went out to our etrailer.com warehouse and successfully fit the INNO square crossbars # IN434 into the Thule Traverse Roof-Rack Foot Pack. The reason they fit is because Inno and Thule square crossbars are the same dimensions, 7/8 inch by 1-1/4 inch.

Just a reminder that these two different companies do not cross fit their products with each other and as a result there is no warranty coverage on this set up.

expert reply by: Timothy G

0

Answer 1

Yes, since the dimensions of the Inno Square Crossbars - Steel - Black - 71" Long - Qty 2 #IN434 are the same as the Thule SquareBar Evo #TH712500 (1-1/4 inches wide x 7/8 inches tall), the Inno Square Bars will fit the Evo Raised Rail Feet…

view full answer...

Answer 2

I went out into our showroom and measured the dimensions of a set of discontinued Thule square load bars and found that they are 7/8 of an inch by 1-1/4 inches. This is identical to the Inno square bars like #INB137.

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 7

The Demco Hydraulic Trailer Brake Actuator part #DM72VR should be a direct replacement for the Atwood 61101 Brake Actuator that you have now. This newest updated it rated at 7K instead of 6K. This is a bolt on option that mounts on 3" centers.…

view full answer...

Answer 8

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 9

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 10

Hi Kyler! We definitely have center caps and lug nuts that you can use, but the Kenda Karrier KR35 ST175/80R13 LRD Radial Trailer Tire w/ 13" Aluminum AM03 Wheel - 5 on 4-1/2 #KE34TJ does not include them. With that said, I recommend the…

view full answer...

Answer 11

Hey Nate, We do not have a 3/4" spindle nut or washer, the smallest option is the 7/8" spindle nut #165931and a 1" washer #SW1000. I cannot find anything smaller. Are you sure the threads on you're spindle are 3/4"? If they…

view full answer...

Answer 12

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Will Inno Square Crossbars Fit Thule Roof Racks Square Feet

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching