Gooseneck Hitch Ball Recommendation for 2017 Ford F-350 with Factory Rail Kit

Question

Question:

Need ball for factory 5th wheel Ford f350 2017. Please advise

asked by: Christian S

0

Expert Reply:

The Reese Replacement Ball part # RP19311 is the correct gooseneck ball for your 2017 Ford F-350 that has the factory rail kit. This will install right into the gooseneck hitch opening you have and you'd be set.

I attached an install video for this ball for you to check out as well.

expert reply by: Jameson C

0

Answer 1

I believe the ball you are looking for is the Reese part #RP19311. This ball fits the Ford factory rail kits and the Reese Elite series gooseneck hitch/fifth wheel rail kits that actually ended up becoming the Ford factory rail kits. Since you have…

view full answer...

Answer 2

The gooseneck ball that came with the B&W Ball and Safety Chain Kit item #BWGNXA2061 is too tall. You will need to use the Curt Pop-In Ball item #C60601 instead. I have linked a diagram below that will show you the dimensions. It does come in a…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 8

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 9

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 10

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 11

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 12

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Gooseneck Hitch Ball Recommendation for 2017 Ford F-350 with Factory Rail Kit

Featured Help Information

Miscellaneous Media

Continue Researching