Replacement Plastic Clip and Strap Recommendation for Extang Encore Tonneau

Question

Question:

I have the Extang Tonno I need the clip that the strap buckle clips into It is screwed to top itself at the front

asked by: Bruce J

0

Expert Reply:

I checked with Extang and for your Encore the Replacement Tie-Down # EX1024 that you referenced is the correct fit.

expert reply by: Jameson C

0

click to enlarge

Answer 1

Based on your images it appears you have a BAKFlip Tonneau Cover. This will use the Buckle and Strap Conversion Kit #PARTS-356A0009. The Replacement Tie-Down #EX1024 you found is for Extang Solid Fold 2.0 Hard Tonneau Covers which are only 3 panels.

view full answer...

Answer 2

The length of the male plastic piece of the Replacement Tie-Down for Extang Solid Fold 2.0 Hard Tonneau Covers #EX1024 is 1-1/2 inches. This is the correct replacement tie-down for the Solid Fold 2.0 Series 83-xxx covers. I have added a link below to…

view full answer...

Answer 3

We do have the whole buckle assembly Replacement Tie-Down for Extang Solid Fold 2.0 Hard Tonneau Covers - Qty 1 #EX1024 If you need just the female end you want Tie-Down Buckle for Extang SolidFold 2.0 Tonneau Covers #EX54560402 available as just the…

view full answer...

Answer 4

The Replacement Tie-Down for Extang Solid Fold 2.0 Hard Tonneau Covers - Qty 1 #EX1024 is what you want for the Solid Fold 2.0. It includes the strap and male buckle, but not the female buckle. If you need that you will want the Replacement Female…

view full answer...

Answer 5

Both the Roadmaster and Blue Ox tow bars are great options. But if it was my decision to make I would go with the Blue Ox Avail part #BX7420 as we have found that the Blue Ox tow bars are a little easier to connect and disconnect from. Also this tow…

view full answer...

Answer 6

To install a Redarc Tow Pro Liberty in your 2023 Toyota Tacoma Sport you will need the following parts: Redarc Tow-Pro Liberty Brake Controller item #RED24FR Plug-and-Play Wiring Harness for Redarc Tow-Pro Trailer Brake Controllers item #RED99FR…

view full answer...

Answer 7

Hey Omar, the removable arms of the base plate kits we offer are not able to be reused on a new vehicle as they are all designed very specifically to fit the exact base plate they were made for. There are fit variations between them even on exact…

view full answer...

Answer 8

Hey Bob, you are definitely thinking in the right direction adding rear support with that much constant weight back there. Between the 320 lbs you’re carrying full time, another 200 lbs with the kayaks, and up to 500 lbs of tongue weight, you’re…

view full answer...

Answer 9

It sure will Robert. The Air Lift 1000 Air Helper Springs item #AL60830 install inside the factory rear coil springs on your 2022 Jeep Gladiator. So long as those springs haven't been swapped out you'll have no problem getting the air bags…

view full answer...

Answer 10

Hey Stacey! To install the Victron Orion XS DC/DC RV Converter #VN93VR you will need appropriately sized wire and fuses. Victron recommends 16 mm² / 6 AWG (13.3 mm²) cable if the distance is less than 5 meters, and 4 AWG (21.2 mm²) if…

view full answer...

Answer 11

Hi Ripu, to flat tow your 2022 Jeep Gladiator behind your 2021 Thor Windsport, you’ll need a base plate, tow bar, safety cables, wiring for lights, and a supplemental braking system. A really solid setup starts with the etrailer Invisible Base Plate…

view full answer...

Answer 12

Hello again Larry, Great question, I am sure there will be a lot of people wondering the same thing. I attached a diagram to help show how to wire up your (2) 100Ah lithium batteries in parallel with the Victron SmartShunt Battery Monitor - 300 Amp…

view full answer...

Replacement Plastic Clip and Strap Recommendation for Extang Encore Tonneau

Continue Researching