Will MaxxAir II Enclosed Trailer Roof Vent Cover MA86JR Fit Standard Vent Cover Mounting Holes

Question

Question:

Will the this cover Maxxair II fit the mounting tabs on the Maxxfan 4500 std tabs?

asked by: Barry C

0

Expert Reply:

Yes, the MaxxAir II RV and Enclosed Trailer Roof Vent Cover # MA86JR can use the same mounting holes as a MaxxAir standard roof vent cover. In fact it will fit most 14 x 14-inch vents.

expert reply by: Adam R

0

Dan Z.

4/6/2020

We have a Maxxair 4000 series vent with rain sensor. Id like to add a vent cover. The FanMate vent cover would be the easiest install with just the EZ Clips but Id prefer the Maxxair II cover for several reasons. What is involved in this installation? Would I have to use the hardware brackets as though I were installing this cover on a different brand cover?

Chris R.

4/7/2020

The Maxxair II # MA00-933075 would work really well with your 4000 Series Vent. Install is more than just a few clips but it's also not terribly difficult. You'll need to drill 4 holes into the vertical frame of the vent so that you can mount the hinged brackets. Once it's in place you'll use the included hardware to install the cover. The bottom of the product page offers a more detailed explanation.

Answer 1

The MaxxAir FanMate Rain Cover in Black #MA00-955002, smoke #MA00-955003, or white #MA00-955001 are confirmed to fit the rounded factory mounting points like you see on the attached photo. If you have the flat mounting anchor points like in the other…

view full answer...

Answer 2

No the MAXX AIR II Vent Cover #MA86JR that you referenced does not come with a bug screen built into it. Just the screen is not available as it does not separate.

view full answer...

Answer 3

You can use the RV Propane Gas Detector #RS64FR (white) or #RS44FR (black) to replace your current Atwood 31013 propane gas detector. This will also use a 12v, 2-wire installation like your current detector.

view full answer...

Answer 4

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 5

Hello Sam; that is a great question! I reached out to Furrion and you will be able to use the Furrion Chill Cube #FR69TD (white) or #FR49TD (black) with your furnace. However, the remote is not capable of operating the furnace at this time. Also, we…

view full answer...

Answer 6

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 7

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 8

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 9

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 10

Hello Bruce, Thanks for writing in! Using butyl tape between the trailer body and the Single Axle Jeep Style Trailer Fender - Diamond Plate Aluminum - 13" to 15" #HP96VR is exactly the route I would go. It stays flexible, creates an…

view full answer...

Will MaxxAir II Enclosed Trailer Roof Vent Cover MA86JR Fit Standard Vent Cover Mounting Holes

Product Page this Question was Asked From

Continue Researching