Installing a Brake Controller on 2011 Chevy Express Passenger Van

Question

Question:

I have a journey 52650 brake controller that I just got for my birthday and want to install it myself on my 2011 chev 3500 express van PASSENGER and want to buy the quick connect at the controller and also BUY the quick connect at the rear tailights to a 7 way flat plug I already just barely bolted on. no wires attached yet. WHAT BRAND AND PART NUMBER OF THE QUICK CONNECT HARNESS DO I NEED?

asked by: Steve

0

Expert Reply:

There is nothing specifically referred to as a quick connect, but in order to install a brake controller you will need a 4-way harness # 118392 which plugs in behind the trim panels in the cargo area on you 2011 Chevy Express Van. You will then need to install the Universal Installation Kit for Trailer Brake Controller # ETBC7 which will include a 7-way plug.

I've added links to reviews of these products for you to take a look at, as well as help articles on brake controllers and installing brake controllers that should be useful.

expert reply by: Kyle S

0

Answer 1

Because your 2011 Chevy Express Van already has a 7-way installed what you'll need to do is find the blue wire that is ran near the emergency brake pedal and connect that to the blue wire of the brake controller. The white wire would get ran to a…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 6

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 7

Since wire color codes are NOT universal, we always recommend wiring by function, rather than wire color. If you look at the Trailer Wiring FAQ article I have linked you to, you can see some diagrams showing the proper way to wire a vehicle and…

view full answer...

Answer 8

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 9

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 10

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 11

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 12

To install a Redarc Tow Pro Liberty in your 2023 Toyota Tacoma Sport you will need the following parts: Redarc Tow-Pro Liberty Brake Controller item #RED24FR Plug-and-Play Wiring Harness for Redarc Tow-Pro Trailer Brake Controllers item #RED99FR…

view full answer...

Installing a Brake Controller on 2011 Chevy Express Passenger Van

Products Featured in This Question

Featured Help Information

Miscellaneous Media

Continue Researching