Is There a Locking Pin for B&W Tow & Stow Ball Mount?

Question

Question:

Is there a locking pin assembly for the tow and stow, pin for the truck and ball assembly to hitch. I saw one for the 180 but doesnt look like it would work on the tow and stow hitch.

asked by: Frank W

1

Helpful Expert Reply:

Yes, for the B&W Tow & Stow, I recommend the Trailer Hitch Receiver Lock for 2", 2-1/2", and 3" Hitches # C23025.

expert reply by: Kyle S

1

click to enlarge

Answer 1

That is a good question, Paul. I am surprised the usable length isn't listed for the Curt #C23025 locking hitch pin. I went out to our warehouse to measure one and it looks like it will fit without issues (I included a quick diagram below with…

view full answer...

Answer 2

The antenna should just twist on and off so if the broken one on your current system is stuck you can use pliers to get a bit of a better grip to assist in unscrewing it, which will allow you to install the Replacement Antenna for Furrion Vision S…

view full answer...

Answer 3

We have exactly the part you're looking for with the Replacement Antenna for Furrion Vision 1, 2, and S Wireless RV Camera Systems #772577. This antenna works with Furrion systems #FCE48TASL-05, #FOS05TASF or #FOS43TASF.

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

Hey John, the Curt QuickPin No Latch A-Frame Coupler part #C84DR that you referenced will work for you but odds are the mounting holes won't line up as basically every brand of coupler does their own thing for mounting holes. So typically all…

view full answer...

Answer 6

The Draw-Tite item #DT73QR installs below the bumper. This hitch is perpetually backordered due to Draw-Tite being bought out so I have a way better option for a hitch for your 2023 Lexus RX 350. I recommend the Curt Trailer Hitch item #C29VV. This…

view full answer...

Answer 7

The correct brake controller harness for your 2023 Ford E-350 to install a Tekonsha Prodigy P3 part #90195 is the part #22292. The connector on your E-350 is in a really unusual location behind the vents above the stereo. To see how to access it…

view full answer...

Answer 8

I have another option for you, but the Fulton Hi-Mount Spare Tire Carrier #FSTC1000301 you were looking at only works with 4 and 5 bolt wheels, and will not work with your wheels that have the 6 on 5-1/2" bolt pattern. Instead I recommend the…

view full answer...

Answer 9

You can certainly adapt a 7-way trailer connector on a trailer to a 4-pole on a vehicle by installing the #37185 adapter you referenced. Simply use the included mounting bracket to install the adapter onto the vehicle, and plug the 4-pole portion of…

view full answer...

Answer 10

Hey Phillip, welcome back. It looks like the top of the receiver with the stock tires is 23-1/4" above the ground on your 2020 Ram 2500. You can confirm this by measuring from the ground to the top inside edge of your trailer hitch receiver. If…

view full answer...

Answer 11

Hey William, so the 3 inch hitches do use the larger hitch pin diameter but the 2-1/2 inch hitches still use the smaller one. So with a reducer like the part #38735 technically you would use both sizes. If you check out the picture I attached you can…

view full answer...

Is There a Locking Pin for B&W Tow & Stow Ball Mount?

Product Page this Question was Asked From

Continue Researching