Air Lift Air Helper Springs Confirmed to Fit a 2002 Toyota Sequoia

Question

Question:

Air Lift 1000, 02 sequoia ! Would these air bags work sufficient for pulling a car trailer? Thanks

asked by: Timmy C

1

Helpful Expert Reply:

The Air Lift 1000 Air Helper Springs # AL60812 are confirmed to fit your 2002 Toyota Sequoia. They'll do great helping you tow your trailer.

expert reply by: Charles S

1

Answer 1

I took a look at the installation manual for both the Firestone Coil-Rite #F4124 and AirLift 1000 Air Helper Springs #AL60812 that fit your 2003 Toyota Sequoia and the directions do differ a bit in terms of cutting the factory bump stop. The…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…

view full answer...

Answer 4

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 5

Hey Gwen! The distance from the center of the mounting hole to the bottom of the Trailer Valet JX Trailer Jack #TV35FR when fully retracted is 13.44". If you’re measuring from the bottom of the pipe mount instead of the center of the hole, that…

view full answer...

Answer 6

Hey Scott, can you send me a picture of the axle tag? The part number will be different from the serial number and Dexter is going to ask me for the serial number to identify it and find the right bearings.

view full answer...

Answer 7

I show the Winnebago Micro Minnie 1800BH has a GVWR of 5,000 so the Equal-i-zer Weight Distribution System part #EQ37100ET is what I recommend. It's rated from 5,000 - 10,000 lbs so you'll be a bit on the low side but this leaves you room to…

view full answer...

Answer 8

In regards to selecting the correct weight distribution system, the loaded tongue weight of the trailer is not the only figure that goes into this. The weight of any cargo stored behind the rear axle of the tow vehicle needs to be added in as well.…

view full answer...

Answer 9

We have actually spoken with Ventline regarding your model AS-13 M-VD0449 in the past and they have confirmed that the correct replacement cover is the part #BVD0449-A03 in Smoke or #BVD0449-A01 in White. The cover measures 14 inches x 14 inches and…

view full answer...

Answer 10

From what I'm seeing the ReadyLIFT 2/3 kit increases the distance between where the ends of the Air Lift 1000 Air Helper Springs for Coil Springs #AL60826 air bags would be making contact on your 2018 Toyota Sequoia so these are not compatible…

view full answer...

Answer 11

With the coil spring suspension enhancement kits like the part #AL60812 that fits the stock suspension of your 2007 Toyota Sequoia there isn't a spacer or way to make them taller if you were to add a lift that increased the travel of the…

view full answer...

Air Lift Air Helper Springs Confirmed to Fit a 2002 Toyota Sequoia

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching