How to Determine if Valterra Flexible Waste Valve Cable Kit # TC372 Will Fit an RV

Question

Question:

I need help identifying my black water waste valve. It looks like your TC372 sort of. I have a picture I would like to send of the one in my trailer to confirm.

asked by: Glen G

0

Expert Reply:

Most likely the Valterra Flexible Cable Kit # TC372 you referenced will be what you need. This is a 3 inch diameter waste valve which is a very common size. The way this installs is very universal as well. The cable is 72 inches as well.

Feel free to send me the picture of yours though as well as the diameter of the valve and I'll verify that it's the correct kit.

expert reply by: Jameson C

0

Answer 1

Both metals help to protect your tank. There are only a few people that have a preference and it is normally based on aluminium being lower on the Galvanic Scale than magnesium so it produces less driving current between the anode and cathode (tank).…

view full answer...

Answer 2

Unfortunately LaSalle Bristol completely covers the connection point in plastic so the only way to gain access to gate inside the LaSalle Bristol Cable-Actuated RV Waste Valve #34466N4BB96GM would be to cut into the plastic for the cord and…

view full answer...

Answer 3

The Replacement Hardware Kit #CE11452-A will hold on your Fulton Boat Guide #FGB1500100. I have included an image of this setup sent in reviewing the product.

view full answer...

Answer 4

Most of the parts you'd looked at are boat trailer guide-ons like #CE27620, is that what you're needing the u-bolts for? If that's the case, for a 3x4 frame member, you'd need part #CES44FR. The only way to get the replacement…

view full answer...

Answer 5

Yes, that is correct John and welcome back! The cable included with the LaSalle Bristol Cable-Actuated RV Waste Valve for Black Water Tank item #34466N4AB48GMA is 48" long. This waste valve is designed to attach to a 3" pipe. How long of a…

view full answer...

Answer 6

Typically it's not going to matter since the bolts are just used to hold the valve body together, so the bolts holding your current waste valve together won't matter. If you waned to use the LaSalle Bristol Cable-Actuated RV Waste Valve for…

view full answer...

Answer 7

Yes the Valterra Waste Valve Body part #TC372 is the same as the Winnebago 129147-02-000 that you have which cross references with T40H.

view full answer...

Answer 8

While I won't be able to tell you the exact length cable you'll need I can help point you in the right direction. The first step is going to be to figure out exactly how your current valve is mounted so that you can remove it and choose the…

view full answer...

Answer 9

Yes, you can swap out the LaSalle Bristol Cable-Actuated RV Waste Valve part #34466N4BB72GM that you have for the Valterra Waste Valve Body w/ Flexible Cable part #TC372. The swap will be a direct, bolt-on replacement as you can reuse the spigot…

view full answer...

Answer 10

For the Valterra #TC372 the bolt pattern is 3-3/4", and the overall length, minus the protrusion, is 13-7/8". For the Valterra #TC172 the bolt pattern is 2-1/2", and the overall length, minus the protrusion, is 9-1/4". I have…

view full answer...

Answer 11

Plumbing parts are interchangeable on RV's just as long as the fittings are the correct size. I couldn't find that exact part number but I believe I have found the Valterra equivalent. If the Bristol valve you are talking about uses the…

view full answer...

Answer 12

The straighter and shorter you can make the dump cables they smoother they will operate to a certain extent. So if you can get away with the shorter 36 inch long cable version part #34466N4AB36GM instead of the #34466N11AB72GMA that you referenced…

view full answer...

How to Determine if Valterra Flexible Waste Valve Cable Kit # TC372 Will Fit an RV

Product Page this Question was Asked From

Continue Researching